3] A pre-stress concrete beam 300mmx500mm in section has a span of 6.6m and is subjected to a uniformly distributed load of 18KN/m including the self-weight of the beam. The prestressing tendons which are located at the lower third point and provide an effective prestressing force of 1060KN. Determine the extreme fiber stresses in concrete at the mid snan section

3] A pre-stress concrete beam 300mmx500mm in section has a span of 6.6m and is subjected to a uniformly distributed load of 18KN/m including the self-weight of the beam. The prestressing tendons which are located at the lower third point and provide an effective prestressing force of 1060KN. Determine the extreme fiber stresses in concrete at the mid snan section

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The concrete in the core of a spiral column is sub- jected to a uniform confining stress o, of 680 psi. What will the compressive strength o be? The un- confined uniaxial compressive strength is 5000 psi.
What is the value of the Whitney stress block parameter, β1β1, for 6000 psi concrete?
A half-block concrete masonry unit is tested for compressive strength. Theoutside dimensions of the specimen are 190 mm X 190 mm X 190 mm.The cross section is a hollow square with a wall thickness of 25 mm. Theload is applied perpendicular to the hollow cross section and the maximum load is 225 kN.a. Determine the gross area compressive strength.b. Determine the net area compressive strength.
A half-block concrete masonry unit is subjected to compression until failure.The outside dimensions of the specimen are 190 mm X 190 mm X 190 mm.The cross section is a hollow square with a wall thickness of 38 mm. The loadis applied perpendicular to the hollow cross section and the maximum loadis 296 kN.a. Determine the gross area compressive strength.b. Determine the net area compressive strength.
The beam cross section: Service loads: Steel young's modulus Es = 29,000,000 psi A 1 kN/m distributed load. Concrete young's modulus Ec = 3,500,000 psi A 10 kN concentrated load located at midspan. 10 kN Compressive strength of Concrete f'c = 3500 psi 1 kN/m Tensile strength of concrete f 'ct = 475 psi Steel yield point fy = 60000 psi %3D A 4.0 m 10" 8.0 m y 1. Determine the stress in the steel bars and concrete 23 bottom and top fibers. 25" 2. What value of the 10 kN concentrated load will cause cracks to appear on the concrete? 3. Determine the stress in the steel bars and concrete 3 No. 12 bottom and top fibers if the value obtained in point #2 is increased by 20%.
A pretensioned prestressed beam has a rectangular cross section of 6 in. width and 20 in. total depth. It is built using normal-density concrete with a specified strength f = 4000 psi and a strength at transfer of f' = 3000 psi. Stress limits are as follows: fi = 164 psi, f. = -1800 psi, f. = 474 psi, and fes = -1800 psi. The effectiveness ratio R may be assumed equal to 0.80. For these conditions, find the initial prestress force P, and eccentricity e to maximize the superimposed load moment My + M, that can be carried without exceeding the stress limits. What uniformly distributed load can be carried on a 30 ft simple span? What tendon profile would you recommend?
A simply supported beam 6.5m long, 350mmx500mm, prestressed with a straight tendon located 150mm below the neutral axis with effective prestressing force, Pe, of 300kN. Total load carried by the beam is 20kN/m. A. Determine the area of the concrete, mm2.B. Determine the section modulus of the concrete in x10^3 mm^3C. Determine the compressive stress caused by the tendon alone if Pe is at the centroid, MPa
Determine the values of the distance cfrom the extreme concrete corppression fibers to the neutral axis, andr, for the beam shown in the following Figure fy 60,000 psi and fc 3000 psi. 0.003 21 in d-c 389 bars 3.00 in) = (0.003) 12 in Select one: a. 6.90 in, 0.0061 b. 6.25 in, 0.0069 c. 7.50 in, 0.0085 d.5.93 in, 0.0076
Problem- A doubly reinforced rectangular concrete beam has a width of 30mm and an effective depth of 500 mm. The beam is reinforced with 2200 mm² of steel in tension and 628 mm² of steel in compression. The effective cover for compression steel is 50 mm. Assume that both tension and compression steel yield. The grades of concrete and steel used are M20 and Fe250, respectively. The stress block parameters (rounded off to first two decimal places) for concrete shall be as per IS 456 : 2000. Find the depth of neutral axis.
Pre-stressed.
Correct solution
A rectangular beam with width of 233 mm and overall height of 431 mm is prestressed by using a bonded (stress relieved) tendons with a specified tensile strength of prestressing tendons fpu %3D 1380 MPa. Strength of concrete is 33.1 MPa. The area of presstressed reinforcement in tension zone is 1,024 mm2 and its centroid is located 40 mm above the bottom end of the beam. The specific yield strength of prestressing tendons fpy = 1220 MPa. Compute for the ultimate moment capacity of the beam.