3-98 The hull of a boat has a volume of 180 m³, and thetotal mass of the boat when empty is 8560 kg. Determinehow much load this boat can carry without sinking (a) in alake and (b) in seawater with a specific gravity of 1.03.

Given Volume = 180m3 Weight of boat = 8560 kg Load(W) =?

Answered: 3-98 The hull of a ba bo total mass of…

Engineering

Civil Engineering

3-98 The hull of a ba bo total mass of the boat how much load this boa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Sign 700 mm = 300 mm

Q: In the truss shown all the members are pin connected at their ends, support A is a pin and support E…

A: Given structure is a truss with two supports, 14 members, and 8 joints. number of members, m= 14…

Q: A steel column of rectangular section 10 mm * 5mm and length 0.5 m is simply supported at both ends.…

Q: 2- Calculate the design ultimate load Wu on the on the beams B1,B2, B3, B4 3.6 m 4.8 4 m Assume: DL…

Q: The beam is loaded as shown. which of the following nearly givės the flexural stress due to…

Q: A thin, homogeneous disk of mass m and radius r spins at the constant rate Vị about an axle held by…

A: Consider the figure,

Q: Results from a direct shear test on a sandy soil are given in the following table. The shear box is…

Q: H.W A rigid Slab weighing 600 K bronze vads and one Steel Vocd Cach off 6000 mm2 area at a…

A: As per guidelines we are supposed to answer only first question so please repost rest questions…

Q: quV0= 0 rwob V 08 3.73 A 12-ft beam is loaded in the various ways represented in the fig- ure. Find…

Q: The beam is loaded as shown. which of the following nearly gives the flexural stress du to tension…

A: Find the reactions :RA=RB=12×4+2×12×12×42=48kNMax moment will be at the midspan…

Q: PROBLEM SET Situation 1 The rigid bar AB, attached to two vertical rods as shown in the figure, is…

A: Given:- The rigid bar AB is attached with two vertical rods Modulus of elasticity of the steel rod =…

Q: 1. Portal Method The frame shown is subjected to lateral loads as shown. Supports S, T, U V, W and X…

Q: Problem 1 A beam is supported as shown below: A D E F Hinge Hinge 5m 5 m 6 m 3 m 3 m The beam is to…

Q: A truss has geometry and loads as shown in the figure and parameter table. Use method of sections to…

Q: I Determine the components of all forces acting on each member of the loaded frame. 5 kN 1.5 m 1.5 m…

Q: am fotografiar gorüntule + Şuraya ekle: % Duzenle ve Okuştur Paylas Learning Goal: Part B- Reaction…

A: Finding out the forces in beam for different conditions.

Q: Estimate volume of this beam. Length of beam=5m 6016mm 60 16 mm Section 1-1 y u oz qo -0.40 m-

A: From the given section, Width of the beam, B = 0.40 m Depth of the beam, D = 0.40 + 0.20 = 0.60 m…

Q: Neglect beam sel f weight,if: fpcad of live) H,w.2 Find the makimum Service loads That the beam…

A: We will find the maximum service load (dead and live) according to ACI-18 in the steps as given…

Q: 13/13 FOR THE RIGID BEAM SHOWN BELOW FIND THE STRESS IN STEEL ROD. Ast3 200 mm2, Aalu=300 mm2 Steel…

Q: Determine the design strength of a T-Beam with the following data: bf = 700 mm bw = 300 mm he = 100…

Q: 1.) In the H20-44 truck loading, the 44 means? CHOICES: a.) Total weight of truck in ksi b.)…

Q: A steel column is loaded with a centric normal force. The pillar is articulated in the foot and top…

A: Safety will be assessed by EUROCODE Le = Effective length = L = 6.5 m ...(As per statement given…

Q: Hiwe A bar with constant ss-section area(Aland unit weight () is subjected to axial force ce) in…

Q: (including P= ? beam weight) P=? fy = 60,000psi Wp = 3 k/ft ar = 5 k/ft %3D 15" 42" 4#10 bars 3"…

Q: What will be the safe weight pe linear meter length of the beam if the displacement at E is limite…

Q: correct Question 2 Using the Equilibrium equations calculate Reaction Ay for the truss shown below,…

Q: Calculate the moment of resistance of a doubly reinforced T- beam as shown in Fig. 7.9 having a…

Q: classify the following according to stability and determinacy . a. frame A is classified as? b.…

A: Ds=3m+R-3j -€(m'-1) m=number of members R=external support reaction j=number of joints m'=number of…

Q: For the given properties of the beam below, determine the safest wy that the beam will carry. bf =…

A: Solution:- Neutral axis of section, by assuming tf<37xu ⇒ 0.36fc×bw.xu+0.45fc×bf-bw×tf =0.87fy×As…

Q: Determine the member force 2-4, 3-4 and 3-5 ,4 kN > 4 kN 8 kN 2 4 kN 3 2 2 Member 2-4 [ Choose ]…

A: Given:- a truss as shown below:

Q: For the given properties of the beam below, determine the safest wy that the beam will carry. bf =…

A: fc = 34.5MPa fy = 400MPa

Q: Design a sliding gate wing type of beams (W840) which have an elastic section modulus equal to 582…

Q: Hiw A Pismatic steel bar ofa Square cress section (look lo0)mm is loaoled by comperessive force P=…

A: Given: The cross-section of the steel bar is 100 mm x 100 mm. The compressive force P is 1300 kN.…

Q: C. yielding. D. shear rupture 5. On steel structures the dead load is the weight of A. steel work.…

A: Before answering this question need to know about dead weight- Dead weight or dead load is that load…

Q: Determine the design strength of a T- Beam given the following data: b = 700 mm bw = 300 mm hf = 100…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

3-98 The hull of a boat has a volume of 180 m³, and the
total mass of the boat when empty is 8560 kg. Determine
how much load this boat can carry without sinking (a) in a
lake and (b) in seawater with a specific gravity of 1.03.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the volume of water displaced and position of center of buoyancy for a wooden block of width 2.5 m and of depth 1.5 m, when floats horizontally in water. The density of wooden block is 650 kg/m³ and its length is 6 m.
A wooden cylinder of sp. gravity 0.6 and diameter 0.4 m is required to float in an oil of sp. gravity 0.8. Find the maximum length (in meter) of the cylinder in order that it may float vertically in water.
Soln is required,
HYDRAULICS
BUOYANCY: AN INVERTED CONE 10 CM ACROSS THE BOTTOM AND 12 CM HEIGHT WITH SPECIFIC GRAVITY OF 0.9 FLOATS IN WATER WITH SPECIFIC GRAVITY OF 1.0. (NOTE 1 M = 100 CM) The draft in water of the cone is The displaced volume is The above volume is The total volume of the cone is
Number 11 - 13 only
ISTINYE ISU UNIVERSITY 1STA NSUL Question 3: The structure shown in figure has a cross section that is Water 200 cm composed of a triangular section made of wood (density of wood is 800 kg/m³. An additional layer of Aluminum (density of Aluminum is 2700 kg/m³). Calculate the required thickness of Aluminum that is required to keep surface 3 h 40 cm the upper surface of the structure matching the water surface.
Fluid
A wood cone, 700 mm diameter and 1,000 mm high floats in water with its vertex down. If the specific gravity of the wood is 0.60, what is the distance from the metacenter to the center of buoyancy? 350 1000/4 250 D/4 M B. D 750 3D/4 Waterline Section
QUESTION 1 A solid cylinder is to be 0.25 m in diameter. The base of axial length 25 mm is to be of metal which has a specific gravity of 7, and the remainder of material which has a specific gravity of 0.5. Find the maximum overall length of the cylinder so that it may float in water in stable equilibrium with its axis vertical.
thermodynamics
The dimension of the cylindrical drum is 2 ft in diameter and 3 ft long. An aluminum weights are to be placed inside the drum to make it neutrally buoyant in fresh water. The weight of the aluminum is 0.10 lb/in3 and the drum when empty weighs 30 lb. What volume of aluminum is required?