*3-10 An overhung diving board is shown in Figure P3-4a. Find the reaction forces and construct the shear and moment diagrams for this board with a 100-kg person standing at the free end. Determine the maximum shear force, maximum moment, and their locations.

*3-10 An overhung diving board is shown in Figure P3-4a. Find the reaction forces and construct the shear and moment diagrams for this board with a 100-kg person standing at the free end. Determine the maximum shear force, maximum moment, and their locations.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

show solutions pls thank you very much :D
Problem # 1 A 1ok For the pinned frame in the figure, calculate the pin forces acting at point B, on member BD (magnitude and direction). B dol 4'
In the figure, a nonuniform bar is suspended at rest in a horizontal position by two massless cords as shown in the figure here. One cord makes the angle 0 = 31.1° with the vertical; the other makes the angle p = 58.9° with the vertical. If the length L of the bar is 5.9 m, compute the distance x from the left end of the bar to its center of mass. L com
The Straw Hat crew on their journey to Laugh Tale Island found a big treasure box (W). Luffy wanted to place the treasure box (W) as shown in the figure. A 100-mm x 300 mm rectangular beam is supported in a horizontal position. At point "A", it is being held by a pin and at "B" by a cable BD inclined 3 vertical to 4 horizontal. Assume all forces are applied to the beam along its central axis. Given that Fcparallel to grain = 10.50 MPa, W = 79 kN and E = 13800 MPa. Neglecting the weight of the beam and cable, determine whether the design is safe. Cable 2.4 m 2.4 m
points A, B and D, respectively, as shown in the figure. A uniformly distributed loac of 4 kN/m acting vertically downwards extends for a length of 4 m between point A and C. Page 3 of 6 5 kN 10 kN 4 kN/m A 2 m 2 m 1 m 2 m 30 kN Figure Q2: A cantilever beam 2.1. Calculate the magnitudes and directions of the support reaction force RE and bending moment ME and at point E. 2.2. Establish the equations of shear forces (SF) and bending moments (BM) for each span of the beam. 2.3. On the basis of the established equations for SF and BM for the cantilever beam, construct the shear force and bending moment diagrams along the entire span of the beam. 2.4. Determine the magnitude and position of the maximum bending moment acting on the beam. 2.5. Calculate and show the positions of the points of contra-flexure (PCE)
A 120 N is at rest on a rough in a line making an angle of 20° with the horizontal. The roller has a radius of 0.40 m. as indicated in the figure. a.Calculate the force P that is required to push the roller at rest on the rough incline surface. b. Calculate the normal reaction at the point of contact between the roller and the rough inclined surface. c.Calculate the force P required to pull the roller at rest on the rough incline surface.
A simply supported beam is subjected to the load distribution shown in figure, which is symmetrical about the middle of the beam. What would be the reactions at the supports? (Use SI system if your roll number is less than or equal to 100 and use US customary system if your roll number is greater than 100). (Roll No 196) Also replace this force by an equivalent force couple system at the right edge of the beam if your roll number is odd and replace this force by an equivalent force couple system at the left edge of the beam if your roll number is even. The load type is Elliptical, w, = 415 L= Any value of your choice 2L Figure for Question No.1
For the frame shown below, • Calculate the support reactions at A and C Calculate the internal force at D 8m B D 50 kN 10m A 6m 6m
The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain automobile distributors. For the configuration shown, where the wrench lies in a vertical plane and a horizontal 150-N force F is applied at A perpendicular to the handle, calculate the moment Mo applied to the bolt at O. For what value of the distance d would the z-component of Mo be zero? Assume a = 90 mm, d = 130 mm, h = 210 mm, 0 = 16% F Answers Moi d= Mi 0 h i+ mm Mi j+ Mi k) N.m
Short answer please
For the pinned frame in the figure, calculate the pin forces acting at point B, on member BD (magnitude and direction).Hint: Look for two-force members
For the structural frame shown in figure (4), draw the axial, shear forces and bending moment diagrams for member abc. 20 kN/m 3m b 3m a ZRoller Pin 4m 4m Figure (4)