2m m 2m 1m I'm •G 1n

Q: The system shown is in equilibrium by the applied 250 N-force. Determine the pin reaction D. Neglect…

A: Given data: The applied load is P = 250 N. The horizontal distance between A and O is x = 125 mm.…

Q: 10 m 0.5 kN downward 0.5 kN upward 5 kN-m C

A: Option b is correct.

Q: If the mass of the flowerpot is 65 kg, calculate the tension generated in every cable for…

A:

Q: Determine the reactions of the frame’s supports and the horizontal and vertical components of the…

A:

Q: Determine the angle θ for equilibrium of the lever shown in the figure. Disregard the weights of…

A: When all of the forces or moments operating on a structure are balanced, it is said to be in…

Q: How about this part :"Determine the x and y components of reaction the pin C exerts on member EDC…

A: F1 = 8 KN

Q: Bar AB of Fig. with weight W and length L has a uniform cross section. The spring has an unstretched…

A: Write the expression of the length of the spring. Write the expression of the change in length of…

Q: Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable…

A:

Q: The uniform 15-m pole has a mass of 150 kg and is supported by its smooth ends against the vertical…

A: Given:m=150 KgL=15 m

Q: E G 100 kN 3 m to 200 kN 3 m B 4 m

A: Force in member BC is 375 kN [Compression] and force in member CG is 125 kN [Tension].

Q: The mass center G of the 1350-kg rear-engine car is located as shown in the figure. Determine the…

A:

Q: The vertical mast supports the 6.2-kN force F and is constrained by the two fixed cables BC and BD…

A: Given:The force is .The distances are .The system is shown below.To find:The tension in the cable .

Q: The light right-angle boom which supports the 560-kg cylinder is supported by three cables and a…

A:

Q: Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable…

A:

Q: 4-42. Determine the horizontal and vertical compo- nents of the pin reaction at B of Fig. P4-42 on…

A: Given: The frame is shown below:

Q: P23-2. The homogenous door shown has a mass of 60 kg and is held in the position shown by the rod…

A: Free-body diagram: Free-body diagram is a diagram that represents all forces acted on the body. The…

Q: Bar GHJ is subject to a 25 lb force and is supported by a pin in a smooth slot at G, a weightless…

A: The link at H is weightlessThe weight of GHJ is

Q: Problem Statement Based on Problem 6-11 from the textbook. The spring has an unstretched length of…

A:

Q: Ihas a weight of 4 Ib/ft. I is supported by a bail- ket joint at C and a journal bearing at D. The…

A:

Q: Determine the reaction at C

A: Given data: M=5 kN.m Need to determine the reaction force at C.

Q: Q/. Determine the normal reaction at the roller A and horizontal and vertical components at pin B…

A:

Q: The square steel plate has a mass of 1690 kg with mass center at its center G. Calculate the tension…

A:

Q: Determine the horizontal and vertical components of reaction on the beam caused by the pin at B and…

A:

Q: The mass center G of the 1235-kg rear-engine car is located as shown in the figure. Determine the…

A:

Q: 2. The uniform slender bar of length 2.05r and mass m rests against the circular surface as shown.…

A: Find value of normal reaction at A and reaction at O.

Q: A uniform bar with mass M = 3.25 kilograms is shown in the diagram. hlo required to keep the

A:

Q: Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable…

A:

Q: Problem Statement Based on Problem 5-74 from the textbook. The bend rod is supported at A, B, and C…

A:

Q: The uniform 21-m pole has a mass of 105 kg and is supported by its smooth ends against the vertical…

A: Given:-m=105 kgPole height= 21mTo find:-Magnitude of the reations at A and B

Q: Consider the following system in static equilibrium. Force vector Facts at a distance" from the pin…

A: (a) Draw the free-body diagram of bar.

Q: Application of Equilibrium Solve for the value of unknown variables   Given P1 = 1.39 KN P2…

A: Draw the free-body diagram of the beam. (a) As in the beam, no horizontal force is present so that…

Q: Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal…

A: Given Mass of beam OC = 74 kg Mass of beam AC = 65 kg Mass of traffic signal = 25 kg To find Forces…

Q: The square steel plate has a mass of 1650 kg with mass center at its center G. Calculate the tension…

A:

Q: 3. Determine the x, y, z components of reaction acting on the ball-and-socket at A, the reaction at…

A: Given , a plate in which a uniformly distributed load of 40 lb/ft acts from A to B  and a moment of…

Q: The light boom AB iS attached to a vertical Wall by a ball and Socket joint at A qnd Supported by…

A:

Q: The weight of the uniform bar AB is W. The stiffness of the ideal spring attached to B is k and the…

A:

Q: The drop gate at the end of the trailer has a mass of 124 Mg and mass center at G. It is supported…

A:

Q: Determine the reaction forces at A and B, and determine all internal forces in the system using the…

A:

Q: the bavs AB and Acare joined by a pain at A and a horizontal cable the Vertical cable carrying the…

A: