2cm 6cm 2cm 6cm

Q: complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101…

A: To determine the internal loading as point E.   Following is the free body diagram of the given…

Q: Construct the shear and moment diagram of the figure below. Note: Support reactions is zero. Thus,…

A: A beam is given such that, the support reaction is zero. At the left support, the shear and the…

Q: 3 cm 7 cm 5 cm 5 cM Detenmine the Folloeing %3D

A: Calculation of area and moment of inertia

Q: Column2 700mm 1 3m Beam2 4 3. 700mm+ Column1- 3 3 1 +350+ . 4 350 15. 2 2 2 Beam3 5m Beam1 1 11 4m…

A: Volume of BEAM 1= (4-0.35/2-1.050/2)*0.35*0.45= 3.3*0.35*0.45= 0.51975= 0.52 m3 Volume of BEAM 2=…

Q: a) Compute the difference in elevation between A and B. b) Compute the difference in elevation…

A:

Q: Q#2 Estimate complete quantities in lintel having the following dimensions. Suppose required data…

A: Given length, L=40 ft =12.192 m Width, W=20 ft=6.096 m Thickness, t= 6 inch=0.1524 m

Q: normal stress = o = omax = For 8kN maximum stress is, 8×0.2 1 -×0.8×0.4² 12 MxCx Ix omax = AM = MyCx…

A:

Q: Determine the force in members GE, GC, and BC of the truss shown in Fig. 6-16a. Indicate whether the…

A: Question is based on the truss subject to hinge and roller support. Loading condition on truss and…

Q: Draw the free-body diagram of each object.

A: Given :- Three objects are given with different loading and support reactions :- To determine :-…

Q: Problem 12.16 Consider the building frame shown in (Eure) Suppose that My 2.6 k/ft and s8 k/ft.…

A:

Q: ACTIVITY 3 1. Classify the Soil 1 according to the USDA textural classification system. Soil 1…

A: To find out the soil according to USDA textural classification system.

Q: sketch the deformed shape.

A:

Q: 2. Get the twist of section A: a) By the elastic equation, indicating the value and direction. b) By…

A: The given figure is shown below:

Q: Draw the figure to an enlarged scale in Isohyetal method

A: The iisohyetal approach is a technique for calculating the average amount of precipitation within a…

Q: 100 N 100 N 100 100 150 250

A:

Q: 1) 2 points B & C were observed from point A where the instrument was set up at a height of 1.25m.…

A:

Q: d 1.59 m d = 5.22 feet Problem 8-12 0-mm-diameter concrete pipe is laid on a slope of 1 m per 500 m…

A: To Determine From where sinθ is taken from, in the solution given.

Q: 14" 4.00" 14 1.5" A3 Bare12 Au 8 6 Bars 1. Área of Steel, As, for the column = 2. What % steel is…

A: The area of the steel reinforcement is equal to the sum of the area of the longitudinal…

Q: Two identical trusses support a load of 100 N as shown in the figure. The length of each truss is…

A: Given Load 100 NLength 1 mCross section 200 mm2Elasticity modulus 200 GPaTo find out Force in member…

Q: Tg = 1200 N-m %3D A Tc = 400 N-m 40 750 mm 30 C 600 mm

A:

Q: 3) Cross-Section Hethod Given the reservoir and sections shown below, deternine what is asked for.…

A:

Q: a) Calculate the settlement of the 15 ft thick clay layer (Figure 1) that will result from the load…

A: Width of footing = b = 4.5ft Length of footing = l = 4.5ft Wight of clay layer = H = 15ft. X = 30.…

Q: -Compute the plastic section modulus of the following section and its corresponding moment capacity.…

A: to find - plastic section modulus (Zp) and corresponding moment capacity (Mp)

Q: Is used to create parallel lines, concentrated circles and parallel curves A. Copy command B. Offet…

A: Command used to create parallel line, concentric circles and parallel curves

Q: Rod AB consists of two cylindrical portions AC and BC, each with a cross-sectional area of 1950 mm².…

A: Deflection is the amount that a portion of a structural element moves under a load in structural…

Q: Determine which of the lines shown below are parallel to each other.

A: If 2 lines seem parallel to 2 ADJACENT views, we will able to conclude that these lines are…

Q: Situation #1 The compound beam is pin supported at C and supported by a roller at A and B. There is…

A: As per company policy we can only answer first three questions Kindly post other questions as…

Q: 4cm r=2om 12cm r=2cm 4cm 3cm 6cm 3cm '(c)

A:

Q: what force t is required to drag an 80-kg aluminum box across a steel ploor īp it is applicd at an…

A: Given Data: Weight of the aluminum box is W=80 kg. Angle of inclination of the floor is θ=40°

Q: Solutions must be based solely on the method of joints. 1. The suspended object has weight W. Both W…

A:

Q: what will be dimension of sides of the square ? Solid Mechanics (a) 10 cm (b) 5 cm ic) 12 cm (d) 12…

A:

Q: subtract the numbers 557                                   -125

A: The process of deduction of quantity is known as subtraction.

Q: Q#2 Draw the Mohr,s circle for the stress element shown in figure. Determine the principal stresses…

A:

Electric Circuit and Components

An electrical circuit or electrical network is a pre-determined pathway to make the electrons flow in the desired direction. The flow of electrons will set up a current flow in the circuit. Normally, the flow of electrical current is opposite to the flow of electrons. An electron is a fundamental sub-atomic particle of an atom possessing a negative charge. To initiate the flow of current and achieve the desired output, the electrical circuit should necessarily be composed of closed pathways. The pathways are made-up of good conductors of electricity such as aluminium and copper.