Answered: 2a. If a computer runs at 12.8 GHz,…

2a. If a computer runs at 12.8 GHz, what is the period of its clock signal? 2b. If the period of a periodic pulse train is 125 nanoseconds, what is the signal's frequency

C++ for Engineers and Scientists

4th Edition

ISBN:9781133187844

Author:Bronson, Gary J.

Publisher:Bronson, Gary J.

Chapter7: Arrays

Section7.5: Case Studies

Problem 15E

See similar textbooks

Similar questions

Question 9 Not yet answered Marked out of 1.00 Flag question A coil is wrapped with 300 turns of wire on the perimeter of a circular frame (radius = 8.0 cm). Each turn has the same area, equal to that of the frame. A uniform magnetic field is turned on perpendicular to the plane of the coil. This field changes at a constant rate from 20 to 80 mT in a time of 20 ms. What is the magnitude of the induced emf in the coil at the instant the magnetic field has a magnitude of 50 mT? O 15 V O 10 V O 18 V OOO 30 v O 24 V
Given is a sine wave in time domain, using this wave plots answer the following: 1 second ww. Time A- How much is the wave amplitude with its unit? Answer B- How much is the wave frequency with its unit? Answer C- Draw the same wave in the frequency domain Answer
A voltmeter with an internal resistance of 100 KQ is used to measure the voltage Vab in the circuit shown below, what is the voltmeter reading? 36v R1-12 KQ M 30 18 mA R2=60 kQ R3=15 ΚΩ M + Vab Note: All students are welcomed to solve it, however assignments are mandatory for old students only.
In MATLAB Code
subject (electronics for computer engineering )
Using matlab to compute if you can.
R-2000 2 An electrical capacitor with an unknown capacitance is connected to the circuit shown. The switch is first connected to B and the capacitor is charged. Then, the switch is connected to A and the capacitor discharges through the resistor. As the capacitor is discharging, the voltage across the capacitor is measured for 10 s in intervals of 1 s. The recorded measurements are given in the table below. Vo | 3| 4 | 5 | 3.55 2.81 6 7 1.26 | 2 8 10 V(V) | 9.4. 7.31 | 5.15 2.04 0.97 0.74 | 0.58 You recall from PHYS2102 that the voltage of the capacitor, during a discharge, as function of time is given by V = V, e*t/(RC) This exponential equation can be written as a linear equation of In(V) and t in the form : In(V) = t + In(V6) Use Matlah to do the following: "In all graphs add title, sgend and axis labels 1. Estimate the time at which the voltage V = 6.5 V. 2. Estimate, using spline interpolation, the voltage V1 corresponding to 30 times varying from 1 to RC 10s. 3. In the same…
The voltage Vc (t) (in V) and the current i(t) (in Amp) after closing the switch in the circuit shown in Figure Q2 are given by: -v, (1 -e+) i(t) Vc (t) = V. (1 – e' Vo e R ic(t) T = RC where R = Resistance C = Capacitance Figure Q2 T = Time constant Consider the case where Vo = 30 V, R = 2000 N, and C = 3000 µF b) Assemble your user-defined function with necessary MATLAB code to obtain V, and ic when t = 20 s.
SOLVE IN MATLAB. How would I write the code for this in matlab?
A standard science experiment is to drop a ball and see how high it bounces. Once the “bounciness” of the ball has been determined, the ratio gives a bounciness index. For example, if a ball dropped from a height of 10 feet bounces 6 feet high, the index is 0.6 and the total distance traveled by the ball is 16 feet after one bounce. If the ball were to continue bouncing, the distance after two bounces would be 10 ft + 6 ft + 6 ft + 3.6 ft = 25.6 ft. Note that distance traveled for each successive bounce is the distance to the floor plus 0.6 of that distance as the ball comes back up. Write a program that lets the user enter the initial height of the ball and the number of times the ball is allowed to continue bouncing. Output should be the total distance traveled by the ball. Please name your function "bounce" that has three arguments (initial height, index, number of bounce) and return the total distance traveled by the ball. (float) Skip the part where users can enter the inputs of…
Q1:For the following circuit find voltage gain, current gain input impedance ,output impedance output voltage and F if the input voltage is 10 mv , Bi=200 ,B=180,Rc=2kQ,RBI=180 k0,RB2=47kQ,RE=lkQ,RL=18 kQ,Vcc=20 and ,Cg=Cg=20µF CC [10] M RC Ros RL V o Ca CE
using MATLAB