2A Va 223 4-2 ww 3√ t Vb AMW 282 cs Scanned with CamScanner Find the ff: (use hodal analysis) Direction of current through 2-ohm resistor current through 4t- ohm revistor: (milliamperes) 6--2 current illiame * Current through 2-0h m 5v 4ohm resistor current 1 through 8-ohm resistor:

Q: Find lo in the network shown. 3 k2 6 k2 I. 12 mA 4 k2 2 k2 Select one: Oa.6 mA Ob.4 mA

A: In the network Find the voltage Io We are solving this problem using current division method

Q: The integrator summing the area under a waveform or a curve over unlimited period of time

A: Let us consider a wave or a curve.

Q: Calibrated attenuators are used in digital multimeters to the signal level O a. Increase O b.…

A:

Q: In the figure shown below, the duty ratio of the buck converter is a and the duty ratio of the boost…

A: Given- Duty ratio of buck converter is α. Duty ratio of buck converter is β. Input voltage of buck…

Q: Differentiate the two types of instruction in PLC. COUNT UP COUNTER, COUNT UP/DOWN COUNTER

A: We need to differentiate between the two types of instruction in PLC. COUNT UP COUNTER COUNT…

Q: In the digital circuit given below, the 'F' is equal to B Do

A: Given Boolean circuit:

Q: For a six-bit D/A converter, draw an R/2R ladder network and determine the output voltagen for…

A:

Q: The resolution of an 8 bit A/D converter for a 110V input range is 39.22mV/LSB 10V/LSB 8mV/LSB O…

A: Given that  8 bits n = 8  Full scale value VFS = 10 Resolution = VFS/2^n

Q: the major portion of the majority charge carrier supplion by the emitter is called. collector others…

A: The solution is given below

Q: The input voltage of a Boost converter is 10V, the duty cycle of the boost converter is 0.25. What…

A: Given: Boost converter, Input voltage, Vin=10 V Duty cycle, d=0.25

Q: In a common-source amplifier, the output voltage is taken at the source taken at the gate in phase…

A: The output of a common source JFET amplifier is taken at drain terminal. the typical circuit of…

Q: e self-bias circuit of F ould be biased at V GSQ

A:

Q: Q4) what is the wrong of the following instructions a) MOV DS, SS b) MOV CL, CS c) OUT AX, CL

A: DS and SS are segment registers. In MOV instruction, segment registers cannot be copied directly.

Q: Question 29 29. Determine the rate of change of the output voltage of the circuit when a 2.5v step…

A: Given data, R= 10 kΩ, C= 0.01 μF Circuit diagram is given as,

Q: An overdamped second order system has what type of output?

A: In this question we need to choose a correct option

Q: In re The process of comparison of an instrument with absolute instrument is called

A: The solution is given below  The process of comparison of an instrument with absolute instrument is…

Q: (a) Determine the output level (maximum positive or maximum negative) for each comparator in Figure…

A: The question is about output of comparator.

Q: Using KVL state the transfer function of the following Sallen-Key:

A: Given- Sallen key Op Amp- Resistance = R1 and R2 Capacitance = C1 and C2   To find- Transfer…

Q: R = 2.7 ka R, - 120 ka B = 120 Re = 1 ka

A:

Q: Vec 14 The following IC diagram is for GND O a. AND 7411 Triple 3-input O b. NOR 7427 Triple 3-input…

A:

Q: Determine the output peak voltage, Vo R1=11599 ohms, R2=8534 ohms, R3=8814 ohms, R4=8859 ohms, with…

A: In this question we will find peak output voltage of opamp...

Q: Design a full Subractor using Full adder  to the decimal number 18 from 38  Show all necessary…

A: According to the question we have to, Design a full Subractor using Full adder  to the decimal…

Q: If input voltage of a stage is 1V and the stage has loss of -6dB, what is the output voltage? 2, 000…

A:

Q: Forward converter has the followings R=15 ohm VS=60V Lx=0.5mH Lm=7 mH C=100µF Determinethe output…

A:

Q: 20. A dummy strain gauge is used in a quarter Wheatstone bridge circuit to (a) measure applied…

A: A strain gauge is an electrical sensing device it's resistance varies with the applied force,

Q: In saturation, Vce is O equal to Vcc maximum O minimum O 1 V

A: When base emitter and base collector junctions are forward biased transistor said to be in…

Q: The base current is 35.04 mA and current gain, Boc is 144. The collector current in A is

A: The solution can be achieved as follows.

Q: Derive the Stability Factors for the voltage divider bias configuration *

A:

Q: Operational Amplifiers] Determine I and Vout

A: In this question,   We need to determine the voltage Vo and current I as shown the circuit.  We are…

Q: |4. In the circuit VREF = 2.5 V, and VIN = 1.5 V. The output voltage is Vo VOUT VIN VREF 6-Vcc (a)…

A: Given vi = 1.5 , Vref = 2.5  Find output voltage

Q: In saturation, VCE is minimum O maximum O equal to VCC O 0.7 V O None of these O

A: We need to saturation collector to emitter voltage.

Q: the voltage on the output Y (Vo) Ο 28 O-X 0 -2X Ο 2X+1 y 1 ΚΩ 1 ΚΩ ww x

A: The above amplifier is a non-inverting amplifier. The amplifier is shown below:  The voltage gain…

Q: vcc 12V SRC RB 2.2kn C1 470k. C2 b 5.6µF Vo B = 100 Vi 5.6µF . ro = 00 RE 6800 What is the value of…

A:

Q: The PUT controlling is done through O Anode and gate OCathode and gate OGate

A: In this question we need to choose a correct option

Q: Which one of the below system is a closed loop system O system in which output has to be measured…

A: Closed loop system properties: It is a system in which the output has to be continuously monitored…

Q: A multiplexor is a combinational circuit that passes multiple data inputs to multiple data outputs O…

A: We need to determine the number of inputs and outputs in a multiplexer.

Q: Calculate the common-mode output voltage and A, voltage gain for the circuit below, where V = 5mV,…

A:

Q: Implement a full adder with 2 4x1 multiplexer

A: