2A 62 ww 10V 20 42 82 OA. VTH 10 V O B. VTH= - 12 V OC VTH 22 V OD. VTH= - 10 V OE. VTH= - 22 V OF VTH=12 V www. www ww

Q: Find Vout. 700 mVpp Vin + + V -V Vout

A: In this question,  We need to determine the output voltage of the op amplifier circuit.  We are…

Q: Vcc +15 V Rc 1.0 kN C R 22 kΩ oV out BDc = 200 10µF in 104F R2 * 4.7 kN RE 390 N 100 µF

A:

Q: For the network in following figure, i) Identify the biasing configuration ii) Determine Ipo and V…

A:

Q: 3. Determine Vx. 60V 25.0 n 40n 1252 M + V+ - 240 $8.n :24.0 €24.2 JA

A: We need to find out the unknown voltage for given circuit we will use nodal analysis and voltage…

Q: For the following circuit, determine the maximum power, PMax in Watts that can be transferred to the…

A:

Q: Refer to the Figure below, calculate Z, if VDD = 9V, RG-1Mohms, Rs-2.1kohms, lpss=16mA, VGsQ = -3.2…

A: We need to find out the output impedance for given circuit

Q: Given the following network determine the total Ri,Av,Ai and Ro if hie=2KQ and B=175. *

A:

Q: .CuFor the network shown in figure,determine the input impedance, output impedance,voltage current…

A: Given hie=1.6k ohm,hre=2*10-4 , hfe=110 ,hoe=20us. Rc=2.2 k ohm , RL=1.1k ohm,   R1=50k ohm R2=50k…

Q: When the given Delta circuit is converted to Wye circuit, the resistance values in the Wye circuit…

A:

Q: A room is heated as a result of solar radiation coming in through the windows. Is this a heat or…

A: Heat is basically due to temperature difference it may be temperature difference between two systems…

Q: Case study 2_part 1 Frequency Variable Vp-p Vrms Resistor (Hz) 10 109ko 320mv 20 109ko 980mV 30…

A: The RMS voltage does not depend on the frequency.

Q: Question) Calculate Vo output, while X-16 and Y=24.

A: For the given circuit the value of the unknown voltage Vo needs to be calculated and the value is…

Q: Where come from this value I=1.20mA? How to find it?

A: In the given figure there is the tapping of 30% in resistance R3. So, R3 is converted into 3 kΩ+7 kΩ…

Q: In a circuit R-L-C in series, R 300 V, XC 300 V and XL 500 V. The average electrical power consumed…

A:

Q: Find RAB in the circuit shown 40 W 2 ko 4 kO 12 ko RAB 3k2 6 k2 BO W Select one Q a. 6 K Ob. None of…

A: Given Data:

Q: Find ZT, YT, IR, IL, IC & IT for the circuit given below in polar form. V, 520° V He www R ´ 2.2 ΚΩ…

A:

Q: Determine Vout for Vin=169 V, R1=234 Ohm, R2=28 Ohm Vin 썰 R1 R₂23 ㅎ bur

A: In this question,  We need to determine output voltage Vout  as shown the circuit.  We are solving…

Q: 48V + 20k ww + 2Vx + I + V₂ 10k 10k www + 12V Determine V₁

A: To solve the following circuit we will use thevenin theorem.

Q: Refer to the circuit below. The Thevenin equavilant voltage seen by the voltage source vo is given…

A: we need to calculate the VTH for the circuit.

Q: The circuit below has values: VT = 120 Vac, f = 24.595 kHz, L1 = 130 mH, L2 = 132 mH, and L3 = 214…

A: The given circuit is a series connection of three inductors.The inductive reactance of the inductor…

Q: 7. In Figure E, use the voltage divider rule to compute the phasor voltage Vo. Frequency is 60 Hz.…

A:

Q: Vmax = 50 volt F=50Hz Vmax = 50 volt F=50Hz Vmax = 50 volt F=50Hz m 30mH 200ohm m 33mH 100uF m XL…

A:

Q: Please answer in typing format

A: Circuit is a series RL circuit.Voltage V= 40<25° VImpedance Z = 8<40° Ω  a)By ohms law,Current…

Q: Q3:For the following network, Calculate the voltage gain, output voltage, input impedance and output…

A: Given circuit Since there is a feedback between input and output so by using Miller theorem,…

Q: Q/230V, 50 HZ.4 Pole. Single Phase Iim has the following equiV alent circuit im Pedances: R. = 2.22…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: j 62 ll HE -j20 12 j20 ll I I -j20 j42 24 Vac -j22

A:

Q: For the circuit shown in Figure Vcc= 12V, Rc- 4ks2 Rs =100Ks2, G transistor RB= 198 ks, Ves=0-2V…

A:

Q: o18 V 4.7 k2 Ic R1 OVc = 12 V %3D VB VE 5.6 kN 1.2 kN

A:

Q: The circuit below has values: VT = 120 Vac, f = 24.595 kHz, L1 = 130 mH, L2 = 132 mH, and L3 = 214…

A: Redrawing the circuit by marking the current and the known values from the given points:

Q: Find Req of the circut 100 10 10 ao Ww ww R 32 40 50 120 odes Ans.=11.22 ww ww

A:

Q: determine the following by DC Analysis. a. IDQ b. VGse c. VDS RD=4 KOhms VGG=2volt

A: Given Data:Required Data:Here, we need to determine a. IDQ   b. VGS   c. VDSQ.

Q: What are the advantage of using large hydro dams over runoff the river systems in generating…

A: Hydroelectric power. - The process of harnessing electric energy from flowing water is called…

Q: the circuit shown, determine load current. 0.32 0.22 a E,= 26 V E,- 24 V R. {0.82 r, = 0.12 r, =…

A:

Q: For the circuit in the following figure, find the circuit External Norton equivalent to load…

A: In the question to calculate the Norton equivalent at the load we have to to short circuit the load…

Q: Question : What is the Vpeak of Vout during 45ms. Question : What is the Vpeak of VS during 15ms.

A: A rectifier circuit is used to rectify the AC power generated by this source to the DC  power that…

Q: Consider the circuit and the graph tor UCH) and ilt) O A. Sp = 0,442 ↑ [V],{A] O B. Sp = 0,859 ↑…

A:

Q: With the help of VBB source, adjust the IC current to 5mA by increasing the IB current. To this…

A: According to question: The value of voltage 'VCE' is calculated as…

Q: For the circuit shown in the Figure, if Vs= 50 V and R = 105 Q, answer the following 2 questions:…

A:

Q: D2 SI D1 D3 V1 VSINE RL ZS D4 K ZENER v1 = + 19 V, R = 3 kQ, RL = 13,7 and zener voltage 5,1 What is…

A: Since in the negative cycle the  germanium diode becomes reverse biased so ooen circuited means no…

Q: 25mA!! With the help of VBB source, adjust the IC current to 25mA by increasing the IB current. To…

A:

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.