28. A centrifugal air compressor compresses 200 cfm from 12 psia to 90 psia. The initial specifievolume is 12.6 and final specific volume is 3.25If the inlet suction lirfe is 4" I.D. and thedischarge line is 2.5" I.D. Determineft-lb(a.) The change in flow energy between the boundaries in-minIb(b.) the mass flow rate inandmin(c.) the change in velocity in fps.

Answered: Image /qna-images/answer/4618aba0-5700-4349-a095-5b3c7aaa818a.jpg

28. A centrifugal air compressor compresses 200 cfm from 12 psia to 90 psia. The initial specific volume is 12.6 and final specific volume is 3.25 If the inlet suction lite is 4" L.D. and the discharge line is 2.5" I.D. Determine ft-lh (a.) The change in flow energy between the boundaries in Ib (b.) the mass flow rate in and min (c) the change in velocity in fps.

28. A centrifugal air compressor compresses 200 cfm from 12 psia to 90 psia. The initial specific volume is 12.6 and final specific volume is 3.25 If the inlet suction lite is 4" L.D. and the discharge line is 2.5" I.D. Determine ft-lh (a.) The change in flow energy between the boundaries in Ib (b.) the mass flow rate in and min (c) the change in velocity in fps.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Vacumm You are designing a vacuum system with a desired equilibrium pressure of 10-7 torr. The turbomolecular pump you are using has a pumping speed of 400 L/s. What is the maximium surface area of the chamber that you can allow, assuming that the outgassing rate per square cm 10-9 torr L/s? Note : total outgassing rate G = ( outgassing rate per area ) * ( area )
Do not provide Ai solution
Figure Q2 is a schematic of pump connected to the 80 mm diameter hose, if the average velocity of the water at the pump. C Neglect friction losses. is 8.50 m/s. Determine the required power output of the pump
A pump with an impeller diameter of 0.02 m, an impeller speed of 58.3 rpm, a * total capacity of 12 L/s, an available head of 70 m, and a brake power of 12 kW is used to pump water. Determine the capacity of a homologous pump with twice the impeller diameter and operating at half the speed. Choices: A.60L/S B.36 L/S C.48 L/S D.72L/S
SITUATION 7: The diameter of the pipe is 100 mm and velocity of oil (SG=0.89) is found to be 3,4 m/s. 32. Determine the mass flow rate. a. 23,77kg b. 23.32 kg c. 33.28 g d. 22.74 Kg 33. Determine the hydraulic radius of the pipe. a. 6 mm b. 3 mm c. 0.025 m d. 0.006 m 34. Determine the slope if n30.015. a. 0.356 b. 0.817 c. 0.524 d. 0.475
Water is pumped through a vertical 5.0 cm cement-lined steel pipe to an elevated tank on the roof of a building. The measured pressure at the discahrge side of the pump is 1380 kPa. What pressure can be expected at a point in the pipe 76 m above the pump when the flow is 9.5 L/s? Use f= 0.023 a.225 kPa b.100 kPa c.75 kPA d.150 kPa PLEASE INCLUDE FIGURE OR FBD
Entrance cross-section 0.032 m2 flow fluid 134a, temperature 50 ° C, It enters at 1200 kPa pressure and 20 m / s speed and from the nozzle at 40 ° C temperature and 800 kPa pressure comes out. The heat loss from the nozzle to the environment is 20 kJ / s. a) Calculate the mass flow rate of the refrigerant b) Calculate the exit velocity of the refrigerant from the nozzle.
6. Kaplan turbine of 1 m runner diameter working under a head of 50 m. If the whirl velocity at inlet = 19 m/s and runner speed = 46.47 rad/s, the hydraulie efficiency of the turbine will be: a. 88% b. 90% c. 94% d. 97%
Suppose that the pump of Fig. is run at 1100 r/minagainst a pressure rise of 210 bar. (a) Using the measureddisplacement, estimate the theoretical delivery in gal/min.From the chart, estimate (b) the actual delivery and (c) theoverall efficiency.
identifuy the limitations that exist within different types of water turbine
The flow energy of 24 li/min of a fluid passing a boundary to a system is 2 kJ/sec. What is the pressure at this point? а. 100 kPa b. 140.39 psi c. 1, 000 kPa d. 871 kPa