28 17 28" 16" -8-0-00 4 NQ. 8 bar 25.5"

Q: in bullet form list structural work of beam

A: Structural work of beam

Q: Draw a figure of door and label it

A: The figure and door is in next step

Q: What is classification scheme for composite materials ?

A: Brief concept introduction- Composite Material- These materials are made up of two or more materials…

Q: Draw the frontside and topview the Shape Shown

A: Asked: To draw the front, side and top view of the given shape.   The required engineering id drawn…

Q: Differentiate quartz and quartzite

A:

Q: In what colors is marble found?

A: To determine: In what colors marble is found.

Q: Fill in the blanks / identification: An L-shape section composed of two 10 mm by 30 rectangles. What…

A: Solution

Q: What do beams develop?

A: Beams are the structural members which are loaded transversely. This transverse load can cause…

Q: What is LAP SPLICING? Illustrate a figure and explain it thoroughly

A: A lap is when two pieces of reinforcing bar (rebar) are overlapped to create a continuous line of…

Q: Compare and contrast "Ordinary Timber and Mass Timber".

A: Answer Introduction Timber is known as a renewable construction material.

Q: GENERAL INSTRUCTIONS: Answer the following questions comprehensively and neatly. FILE. - History of…

A: (1) Structural Analysis is not new as it has evolved over several thousand years. During early time…

Q: Submerge interior and exterior plywood samples in water. Continually apply pressure until…

A: Introduction Plywood for the interior: Interior plywood is a material used for inside construction.…

Q: What is Dimensional Lumber often used for in construction projects?

A: Dimensional lumber is a wood lumber that is cut to pre defined standard sizes These are structural…

Q: What are the differences between plywood, oriented- strand board, and composite panels?

A: Plywood is a material that is made up of wood in the form of wood sheets. Plywood has a relatively…

Q: What is the advantage of composite construction?

A: Benefits of composite construction:

Q: What are the classes of hardboard?

A: Hardboard has high density and high strength, which is a quality substitute for wood and is commonly…

Q: Create a flowchart of modern steel making process and describe each process

A: Steel is an alloy of iron with some percent of carbon. The steel contains less than 2% carbon, 1%…

Q: what is grain elasticity?

A: Grit is the name for what is on a grinding, sanding or polishing tool. It is made up of a hard…

Q: Define Steel bars and how many types of stell bars and  given details of sizes of stell bars.

A: The steel bars are defined as the mesh of various steel wires used in reinforced concrete and…

Q: the moment of the beam has been included draw a sketch a deformed shape.

A:

Q: 3. List and discuss the five main types of defects in timber.

A: Five Main Types of Defects in Timber:    Defects in Timber is mainly caused due to  Natural Forces…

Q: topic is structural shapes/steel search 8 example of cold form steel and state how each are used or…

A: Steel is a main structural material. It is used to bear the tension loads on the structure. Steel…

Q: Give Examples of glued-laminated wood.

A: Wood attached to wood. is a structure made by combining one piece of wood? When bonded with…

Q: PROBLEM 2: Determine the centroidal coordinates ( x-bar and y-bar) of the composite area  shown in…

A: To find centroid

Q: Available steel grades in the philippines and their corresponding properties. ALSO GIVE ALL THE…

A: Structural Steel is a  category of steel used for making construction materials in a variety of…

Q: e. Hinge Hinge Hinge

A:

Q: What factors do you consider when designing a tension member in a steel structure?

A: Tension members are structural elements that are subjected to direct axial tensile loads which tend…

Q: What are defects present in lumber ?

A: A stage in the manufacture of wood, known as lumber or timber, is the processing of wood into beams…

Q: "There are 33 dowels - 10M, each measuring 1110 mm, in a continuous concrete footing. What is the…

A: Length of one dowel = 1110 mm                                        =1.11 m  Total no of dowel = 33…

Q: The web thickness of lightest WT shape is?

A: As per the AISC steel construction manual  The web thickness of lightest WT shape is  =  1/10 inch…

Q: What is the process for making light gauge steel framing members?

A: Introduction: Cold-formed steel framing (CFSF) is a term that refers to members used in light-frame…

Q: From the given axis determine the location of the centroid of the composite section shown in the…

A: The figure is shown below,

Q: what is the Design methods of connections and joints?

A: Connection and joints are major part of the structural engineering. Connection: It is a structural…

Q: List the preferred steel type (ASTM spec) for the following shapes:a. Platesb. W shapesc. C sections

A: The material which is available and cost-effective is known as preferred steel type.

Q: Create your own composite shape (combination of at least 2 "common and distinct" shapes), then…

A:

Q: Give two instances of how church composites are employed in non-structural applications.

A: MATERIALS FOR COMPOSITES : It is described as a material comprised of two or more physically…

Q: PROBLEM 2: Determine the centroidal coordinates ( x-bar and y-bar) of the composite ares shown in…

A:

Q: List the three grading methods that are used for wood.

A: Grading is the process of grouping various types of wood in one or more groups according to their…

Q: Structural panel/Sheets Explain ?

A: Structural Panel : Structural panels are lightweight, flat composite materials that can withstand…

Q: can someone please help me with this? Thank you -) A short square steel structural tube is used as a…

A: