26 Compute the resultant of the forces shown in the figure. F1 F21 m 1 m F4 F3 A F1 = 15 KN F2 = 25 KN F5 F3 = 35 KN F4 = 45 KN F5 = 105 KN %3D

Q: Analyze the given semi-frame and Develop the required equation/solution for every given answer. 1.…

A: Given: Required: shear and moment at the left of C  shear and moment at the right of C

Q: m 2 ate for the support reactions of the following bea 60 KN 40 kN/m 120 kN m The 3 m D min

A:

Q: DETERMINE THE MOMENTS AT SUPPORTS USING THREE MOMENT EQUATIONS. Round off your answers to the…

A: Three Moment Equation : Three moment equation gives the relation between bending moments at three…

Q: Situation 3 The beam shown in the figure 14 is loaded by a concentrated load P and a uniformly…

A: Use equilibrium equations to find out reactions at support. Draw BMD & pick up maximum bending…

Q: Q4. Two forces F₁ and F2 act on the screw eye (Figure 2). If their lines of action are at an angle…

A:

Q: A simply supported beam as shown in Figure Q5 is loaded with point loads of 30kN and 20kN acted at…

A: Consider the equilibrium of all horizontal forces.

Q: The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the…

A: Given: The load P is 39078 N. The length of steel is 1.37 m. The length of bronze is 2.3 m. The area…

Q: Find the force in EG shown in the figure

A: Equiulibrium about y∑ Fy=0-5+FFGsin60=0FFG=5sin60FFG=103kntension

Q: A 3 m long cantilever beam, 200 mm x 300 mm in cross-section carries a total uniformly distributed…

A:

Q: The overhanging beam shown has various forces and a 2.5 N m moment applied to it. The 2.5 N m moment…

A: As the distance between the forces will be: d=0.4+0.2+0.5+0.1=1.2 m

Q: The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the…

A:

Q: Question 6 Three external forces act on a structural member in equilibrium: Force Angle made with…

A:

Q: The column shown is completely free at the top and fixed at the bottom. If the critical load is P =…

A: Given data,  Area = 6650 mm² Ix = 119 x 10^6 Iy = 10.2 x 10^6 P = 100 kN

Q: Draw shear force diagram and bending moment diagram of the beam shown in figure 2 below. Then…

A:

Q: A cantilever beam is subjected to load as in the figure below. Based on the diagram, sketch a…

A: Given:Required:Shear force and bending moment diagram

Q: Two forces F1 and F2 act on a body. The net force on the body is Fnet = 2 Ni. If F1= 10 Ni – 10 Nj,…

A: As per guidlines we can solve one question at a time, please upload separately,Thanks

Q: 3 ft 2 ft Block 1 3 ft (150 lbs) H,-0.35 Block 2 3 ft (100 lbs) 4,=0.2 P.

A: Given: w1=150 lbw2=100 lb

Q: 3.3 Graphs should be drawn directly under and aligned with the beam diagram. Graphs should include…

A:

Q: I. Problem Solving: Answer the following and show your complete solutions. Round off your final…

A:

Q: Problem 2 6200 lb Determine the magnitude and direction of the resultant of the three forces acting…

A: Open the force compoment along the x direction and y direction.

Q: The figure below shows a moving vehicle represented by two moving loads. The two loads are x = 1 m…

A: The moving  vehicle can be treated as series of wheel load at a distance of 1m, passing over a…

Q: PROBLEM 1: Determine the resultant (magnitude and direction) of the three forces acting on the…

A:

Q: A 3 m long cantilever beam, 200 mm x 300 mm in cross-section carries a total uniformly distributed…

A:

Q: A 14.0 m long beam is loaded as shown below and the hinge support is at x-1.8 distance from the left…

A:

Q: A 6m simply supported beam is carrying a uniformly distributed load 600 N/m starting 1 meter from…

A: Given: A simply supported beam of 6 m length with loading on it Required: Deflection at midspan

Q: I need to calculate normal force/ supporting force! 啡 4 kN a = 45° 2 m 5 kN/m 3 m ↓↓ 2 m

A:

Q: A concurrent force system has six forces as shown in Figure Determine the following: A. Magnitude of…

A:

Q: For the beam loaded as shown in Fig.1. knowing that the bending moment at the center of the beam is…

A:

Q: Given the beam below and the loads it carries, what is the maximum positive moment in kN-m? 50 kN/m…

A: Bending moment signs :  Clockwise : negative  Anticlockwise : positive

Q: The simply supported beam shown is under the action of a uniformly distributed load w of 4 kN/m plus…

A:

Q: A frame is loaded as shown in the figure. If Q/EI is the horizontal displacement at C, what is the…

A: P = 78KN

Q: F1 F21 m 1 m F4 F3 F1 = 15 KN F2 = 25 KN F5 F4 = 45 KN F3 = 35 KN F5 = 105 KN %3D A

A:

Q: 1. Beam loaded as shown in the following figure: 10 kN 2 m 10 kN/m 2 m 1 m 1m R2 R1 Answer: Mmax =…

A:

Q: 500 N 200 N 4.05 1.78 m 43 400 N 250 N

A:

Q: QUESTION 1 The two storey frame shown in the following figure acted upon at floor level by…

A: The objective of the question is to determine the probable floor displacements and shear forces in…

Q: F1 1 m F3 1 m F1 70 KN F2 100 KN F3 = 50 KN F4 = 20 KN F4 A F2 F5 = 150 KN F5 Solve the magnitude of…

A:

Q: Express the force as a Cartesian vector.

A: Given:- F=630N To find:- Express force as cartesian vector

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.