*25. ssm A 1220-N uniform beam is at- tached to a vertical wall at one end and is supported by a cable at the other end. A 1960 N crate hangs from the far end of the beam. Using the data shown in the drawing, find (a) the magnitude of the tension in the wire and (b) the magni- tudes of the horizontal and vertical com- 50.0% Beam ponents of the force that the wall exerts on the left end of the beam. 30.0 1960 N Problem 25

*25. ssm A 1220-N uniform beam is at- tached to a vertical wall at one end and is supported by a cable at the other end. A 1960 N crate hangs from the far end of the beam. Using the data shown in the drawing, find (a) the magnitude of the tension in the wire and (b) the magni- tudes of the horizontal and vertical com- 50.0% Beam ponents of the force that the wall exerts on the left end of the beam. 30.0 1960 N Problem 25

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A horizontal plank 4.00 m long and having mass 20.0 kg rests on two pivots, one at the left end and a second 1.00 m from the right end. Find the magnitude of the force exerted on the plank by the second pivot.
a 1001 N uniform beam is attached to a vertical wall at one end and js supported by a cable at the other end 1550 N crate hangs from the far end of the beam find the magnitude if the tension in the wire the angle theta is 21 degrees and phi is 32 degrees length of beam is L
A 355 N uniform ladder of length L= 8.00 m leans against a smooth (frictionless) wal The ladder mnakes an angle of 50.0° angle with the horizontal ground and the force of static friction keeps the ladder from sliding to the left. An 875 N firefighter has climbed d = 6.30 m along the ladder trom the bottom. What is the force of static friction f, between the ladder and the ground? 50.0 O 119 N O 480 N O 727 N O 567 N command eptien
The horizontal beam inFig weighs 190 N, and itscenter of gravity is at its center.Find (a) the tension in the cable and(b) the horizontal and vertical componentsof the force exerted on the beamat the wall.
A uniform drawbridge must be held at a 38o angle above the horizontal to allow ships to pass underneath. The drawbridge weights 55000 N and is 15.0 m long. A cable is connected 3.5 m from the hinge where the bridge pivots (measured along the bridge) and pulls horizontally on the bridge to hold it in place. What is the tension in the cable? Find the magnitude and direction of the force the hinge exerts on the bridge. If the cable suddenly breaks, what is the magnitude of the angular acceleration of the drawbridge just after the cable breaks? What is the angular speed of the drawbridge as it becomes horizontal? What is the velocity of the drawbridge, just before it “hits” (i.e. goes horizontal)?
A unitorm 400 N beam of length L = 4 m is supporting a 2000 N box as shown. Find the tension in the tie rope and the force F exerted by the hinge at point P. T=? L44 A50 F=?
A 6.0 m long ladder AB leans against a smooth wall making an angle of 60º with the floor (Figure 3). The ladder is uniform and has a mass of 20.0 kg.(a) Determine the forces exerted on the ladder by the floor and the wall (i.e. at A and B, respectively).(b) Determine the minimum value of the coefficient of static friction to prevent the ladder from slipping.
A shelf bracket is mounted on a vertical wall by a single screw. S S2 S1 Neglecting the weight of the bracket, and if s = 6.4 cm, s1 the horizontal force component exerted on the bracket by the screw when a 95.2 N vertical force is applied as shown. Imagine that the bracket is slightly loose. 5.4 cm and s2 = 2.2 cm, find =
H 60° Figure 6 G M 8. A uniform rod HG of length 2L m and mass m = 2 kg is hinged at end H, as shown in Figure 6 A mass Mg=100 N is hung at the other end G. A horizontal cable at the midpoint of the rod holds it at an angle of 60° to the horizontal. The cable is under a constant tension T. (a) Draw a diagram showing all the forces acting on the rod and determine the tension T in the cable. (b) Calculate both the x and y components (Fr and F₁) of the force F at the hinge H. (c) Will the net force F at H act along the rod HG? Justify your answer.
KPECTED HAS OCCU... Subject ystem S- rchpool.sona- ems.com man Subject Pool tem Department... 6³ 2 [108 W 24,919 Xx :8: F2 3 6. A 150 kg uniform beam is attached to a vertical wall at one end and is supported by a cable at the other end. Calculate the magnitude of the tension in the wire if the angle between the cable and the horizontal is 8 = 46°. X 1832.64 N E 20 F3 $ 4 R HEATRA MAL 2 7 F4 % 5 T F5 ^ 6 tv ♫ MacBook Air F6 Y & 7 44 F7 U M M | L T E 10 * 8 0 30.0⁰ DII F8 ( 9 Beam A DD F9 O O W F10 zoom B P C F11 ISUIH by mi 04 M vauies or roc puffer d + = F12 delete
Structural member AB is to be supported by a strut CD. Determine the smallest length CD may have, and specify where D must be located for a strut of this length to be used. Take x= 120 mm. 60 mm D. y 20 mm E The smallest length CD may have is mm. The coordinates of point Dare ( and Imm.
help pls