25. A de ible strap single rive butt joint joins two (12) mm plates when the diameter of the rivet is 16 mm and the distance from the centre of one rivet to the centre of the next rivet is 80 mm. Find the efficiency of the riveted joint if the rivets are arranged in a zig-zag riveted joint. The allowable stresses for plates are (oF 80 MPa, t= 60 MPa, oc = 140 MPa) and for rivets are (oF120 MPa, t= 90 MPa, o. = 180 MPa).

25. A de ible strap single rive butt joint joins two (12) mm plates when the diameter of the rivet is 16 mm and the distance from the centre of one rivet to the centre of the next rivet is 80 mm. Find the efficiency of the riveted joint if the rivets are arranged in a zig-zag riveted joint. The allowable stresses for plates are (oF 80 MPa, t= 60 MPa, oc = 140 MPa) and for rivets are (oF120 MPa, t= 90 MPa, o. = 180 MPa).

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.17P: A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight...

See similar textbooks

Similar questions

Consider the copper lubes joined in the strength of the copper is err = 200 MPa, figure using a "sweated" joint. Use the properties and what is the maximum load P]iwathat can be dimensions given. applied to the joint if the desired factor of safety in shear is FS_ - 2 and in tension is (a) Find the total elongation of segment 2-3-4 (
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A tension member is to be constructed of two pieces or plastic glued along plane pq (see figure). For purposes of cutting and gluing, the angle ?? must be between 25 and 45. The allowable stresses on the glued joint in tension and shear are 5.0 MPa and 3.0 MPa, respectively (a) Determine the angle it so that the bar will carry the largest load P. (Assume that the strength of the slued joint controls the design.) (b) Determine the maximum allowable load ?? if the cross-sectional area of the bar is 225
: A cylindrical tank with diameter d = 18 in, is subjected to internal gas pressure p = 450 psi. The tank is constructed of steel sections that arc welded circum fereiitially (sec figure). The heads of the tank are hemispherical. The allowable tensile and shear stresses are 8200 psi and 3000 psi, respectively. Also, the allowable tensile stress perpendicular to a weld is 6250 psi. Determine the minimum required thickness /minof (a) the cylindrical part of the tank and (b) the hemispherical heads.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
A double riveted lap joint with chain riveting is to be made for joining two plates 10 mm thick. The allowable stresses are : o, = 60 MPa; T= 50 MPa and o. = 80 MPa. Find the rivet diameter, pitch of rivets and distance between rows of rivets. Also find the efficiency of the joint.
2. Two plates 16 mm thick are joined by a double riveted lap joint. The pitch of each row of rivets is 90 mm. The rivets are 25 mm in diameter. The permissible stresses are as follows: o 140 MPa ; t= 110 MPa and oe = 240 MPa Find the efficiency of the joint.
4. A double riveted lap joint with chain riveting is to be made for joining two plates 10 mm thick. The allowable stresses are : o, = 60 MPa ; t = 50 MPa and o, = 80 MPa. Find the rivet diameter, pitch of rivets and distance between rows of rivets. Also find the efficiency of the joint. [Ans. d = 20 mm ;p= 73 mm; pb = 38 mm; n = 71.7%]
Please answer the problem. Provide a free body diagram. Show the full, complete and clear solution.
4. The figure shows a riveted lap joint with cover plates connecting two steel plates. Each rivet has diameter of 12 mm and the thickness of each steel plate is 15 mm. (a) Compute the shear stress (MPa) in each rivet due to a force of 10.2 kN applied to the plates. (b) If the bearing stress in the steel plates is limited to 40 MPa, what is the allowable load P (kN)? (c) If the width of the steel plates is 100 mm what is the allowable load P (kN) for a limited normal stress of 20 MPa? rivet sver plate Steel plate elate Eleation View Flan View
A lap joint, consisting of 250 mm × 75 mm wooden plates, is fastened with two(2) rows of 20 mm diameter rivets . There are three(3) rivets in a row. The working stresses are 70MPa for rivets in shear and 140 MPa for plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets.
Solve the given problem. Show the FREE BODY DIAGRAM. Show the COMPLETE and CLEAR solution.