25. A benchmark program is run on a 200 MHz processor. The executed program consists of 1 million instruction executions, with the following instruction mix and clock cycle count Instruction Type Arithmetic and logic Load and store Branch Others Instruction Count (Million) 8 4 2 4 Cycles per Instruction 1 3 4

25. A benchmark program is run on a 200 MHz processor. The executed program consists of 1 million instruction executions, with the following instruction mix and clock cycle count Instruction Type Arithmetic and logic Load and store Branch Others Instruction Count (Million) 8 4 2 4 Cycles per Instruction 1 3 4

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. How do the data retention characteristics of RAM and ROM storage devices differ? 2. What is the purpose and use of the Program Counter (PC), Stack Pointer (SP), and Memory Address Register (MAR) registers? 3. Write an 8085 program to store 4EH in memory location 2840H and store 3EH in memory location 2841H, exchange them and store the result in memory locations 2842H and 2843H respectively. Solve this problem using three different methods. 4. Write a program to exchange the content of memory locations [2801] [2800] with [2803] [2802]. 5. The following program is supposed to add the contents of memory location 2050h to the Accumulator. The program works correctly only part of the time. Show that it is wrong to execute the program and how to correct it. MOV LDA ADC HLT В.А 2050H в 6. In a multibyte addition program, when you must use the ADD instruction? When you must use the ADC instruction? 7- The 8085-instruction set does not include a clear accumulator instruction. Which…
02 (a) How many bits do the registers of the 8086 processor have and which registers can be split into halves and accessed separately? (b) Explain the purpose of segmenting memory" How is 20-bit memory address accessed by the processor? For a logical address (c) of OFS7:0552H. calculate the physical address and show the steps.
For the 8085 microprocessor, the instruction (MVI B, 8-bit data) requires Fetch and Read machine cycles. What is the time in microseconds is required to execute it for a clock frequency of 3 MHz
Discussion: 1. Explain what happens when the instruction sequence below is executed. LAHF MOV [BX+DI] , AH 2. What operation is performed by the instruction sequence that follows? MOV AH, [BX+SI] SAHF 3. What instruction should be executed to ensure that the carry flag is in the set state ? the reset state? 4. Which instruction when executed disables the interrupt interface?
Question: Assume a system comprises 16 GB physical memory with B KB page/frame sie and the instruction set comprises instructions that may need access to one (RET). two (PUSH AL or three (MOV A, B) memory locations to fetch the opcode and operands. Assuming that the system is configured with virtual memory: (a) What is the MINIMUM number of memory frames that must be allocated to a process running in the system? (b) What is the MAXIMUM number of memory frames that can be allocated to a process running in the system?
According to the procedure call standard for the ARM architecture, the arguments are passed in core registers (R0-R3) and on the stack. When calling a function add(10, 12, 31, 45), what is the value of the register R1? Assuming each integer has 32 bits. a. 10 b. 12 c. 31 d. 45
1- Identify the addressing mode for: MOV CX, [1234] 2-The instruction that subtracts 1 from the contents of the specified register/memory location is a. INC b. SUBB C. SUB d. DEC
i need the answer quickly
The microprocessor unit that responsible for instruction queuing is .. O EU O ALU BIU O Segment registers O None of the above
1- Identify the addressing mode for: MOV Cx, [SI] 2- The instruction that adds immediate datalcontents of memory location specified in an instruction/register to the contents of another register/memory location is a. SUB b. ADD c. MUL Share Content Participants
The microprocessor unit that responsible for instruction - queuing is ... EU ALU BIU Segment registers None of the above If AL=05H, the instruction MUL * AL will produce AX=0025H AX=0019H AL=19H AL=25H