25 nm, which çan be used for the spectrophotometric determination of ammonia. OCF 2 OH + NH3 indophenol anion To determine the ammonia concentration in a sample of lake water, three samples are prepared. In sample A, 10.0 mL of lal water is mixed with 5 mL of phenol solution and 2 mL of sodium hypochlorite solution, and diluted to 25.0 mL in a volume lask. In sample B, 10.0 mL of lake water is mixed with 5 mL of phenol solution, 2 mL of sodium hypochlorite solution, and 2.50 mL of a 5.50 x 10-4 M ammonia solution, and diluted to 25.0 mL. Sample C is a reagent blank. It contains 10.0 mL of distilled water, 5 mL of phenol solution, and 2 mL of sodium hypochlorite solution, diluted to 25.0 mL. The absorbance of t three samples is then measured at 625 nm in a 1.00 cm cuvette. The results are shown in the table. Sample Absorbance (625 nm) A 0.361 В 0.608 C 0.045 What is the molar absorptivity (e) of the indophenol product? E = M-'cr

25 nm, which çan be used for the spectrophotometric determination of ammonia. OCF 2 OH + NH3 indophenol anion To determine the ammonia concentration in a sample of lake water, three samples are prepared. In sample A, 10.0 mL of lal water is mixed with 5 mL of phenol solution and 2 mL of sodium hypochlorite solution, and diluted to 25.0 mL in a volume lask. In sample B, 10.0 mL of lake water is mixed with 5 mL of phenol solution, 2 mL of sodium hypochlorite solution, and 2.50 mL of a 5.50 x 10-4 M ammonia solution, and diluted to 25.0 mL. Sample C is a reagent blank. It contains 10.0 mL of distilled water, 5 mL of phenol solution, and 2 mL of sodium hypochlorite solution, diluted to 25.0 mL. The absorbance of t three samples is then measured at 625 nm in a 1.00 cm cuvette. The results are shown in the table. Sample Absorbance (625 nm) A 0.361 В 0.608 C 0.045 What is the molar absorptivity (e) of the indophenol product? E = M-'cr

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

mL When blood is donated, sodium oxalate solution is used to precipitate Ca2+, which triggers clotting. A 122.0-mL sample of blood contains 9.70 × 10-5 g Ca A technologist treats the sample with 100.0 mL of 0.1550 M Na₂C₂O. Calculate [Ca2+] after the treatment. Be sure your answer has the correct number of significant figures. Note: Reference the Solubility product constants (Ksp) table for additional information. M Ca2+ 5
5.00 mL of stock solution is diluted to 25.00 mL, producing solution ALPHA. 10.00 mL of solution ALPHA is diluted to 25.00 mL, resulting in solution BETA. 10.00 mlL of solution BETA is then diluted to 25.00 mL, producing solution GAMMA.
A chemistry student needs to standardize a fresh solution of sodium hydroxide. She carefully weighs out 316.mg of oxalic acid H2C2O4 , a diprotic acid that can be purchased inexpensively in high purity, and dissolves it in 250.mL of distilled water. The student then titrates the oxalic acid solution with her sodium hydroxide solution. When the titration reaches the equivalence point, the student finds she has used 93.2mL of sodium hydroxide solution. Calculate the molarity of the student's sodium hydroxide solution. Be sure your answer has the correct number of significant digits.
ENB Assume the densities of all solutions are 1.0 g/ml and their specific heat capacities 4.184 J/g. Experime The enthalpy change of neutralization Part I 3 NH4OH(aq) + HCl(aq)- NH4CI(aq) + H2O(E) 2.1 Equation of reaction: 2.0 M HCI 2.0 M NH.OH Volume Number of moles 0.05 25 ml 25 ml 0.05 Temperature 15 °C 15 °C eaction Initial Temperature,T Final Temperature, T Change in temperature, AT 15 °C 16.5 °C 1.5 °C Calculation of q- in J (q- = - qsa) 2.2 What is the enthalpy change (AH) in kJ.mol, when 1 mol of acid is 2.3 neutralized?
Consider a 1.000-L stock solution of 9.69 M Na3PO4. A 2.000-mL aliquot is taken from this stock solution and diluted to a final volume of 1.000 L. A 5.000-mL aliquot is then taken from this new solution and further diluted to make a new solution with a final volume of 750.0 mL. Calculate Na+ in the final solution.
A 1.00 gram sample of anhydrous cerium sulfate was dissolved in water. Barium nitrate solution was then added until no further precipitation occurred. The precipitate was filtered from the solution then dried and was found to weigh 1.41 g. Determine the formula of the cerium sulfate. Encom calt is hydrated
A 4.908-g sample of a petroleum product was burned in a tube furnace, and the SO2 produced was collected in 2% H2 O2. Reaction: SO2 (g) + H2O2 → H2SO4 A 27.00-mL portion of 0.00826 M NaOH was introduced into the solution of H2 SO4, following which the excess base was back-titrated with 15.15 mL of 0.01165 M HCl. Calculate the sulfur concentration in the sample in parts per million. Concentration ppm
A chemistry student needs to standardize a fresh solution of sodium hydroxide. She carefully weighs out 400. mg of oxalic acid (H,C204), a diprotic acid that can be purchased inexpensively in high purity, and dissolves it in 250. mL of distilled water. The student then titrates the oxalic acid solution with her sodium hydroxide solution. When the titration reaches the equivalence point, the student finds she has used 90.3 mL of sodium hydroxide solution. Calculate the molarity of the student's sodium hydroxide solution. Be sure your answer has the correct number of significant digits.
A student weighs a sample of potassium hydrogen phthalate (KHP) to prepare a primary standard for a titration. She later discovers that the KHP was contaminated with sugar. To determine the amount of KHP in the mixture, she takes 4.678 g4.678 g of the mixture and make a 100.0 mL100.0 mL solution. The student then titrates 10.00 mL10.00 mL of this solution with a 0.1030 M0.1030 M sodium hydroxide solution. She finds that 15.15 mL15.15 mL of the NaOHNaOH solution is needed to reach the end point.
Part 3: What mass of tin was used to make the tin solution? In a similar experiment, a sample of tin metal was dissolved in nitric acid to produce 28.00 mL of solution containing Sn²+. Titration analysis resulted in the calculation that the concentration of Sn²+ in this solution was 0.65 mol/L. b. What mass of tin was used to make the tin solution? Find the mass of the Sn(s) in g: (give your answer to 2 decimal places) Your Answer: Answer
Virtual graduate student Sherry Molestonecraft is assigned to help you carry out the standardization of your NaOH solution. She weighs out 1.30 grams of solid KHP (molar mass 204.2 g/mol) and dissolves it in about 50 mL of water in an Erlenmeyer flask. She then titrates the KHP solution to the equivalence point using the NaOH solution described in Question 1 above. The volume of NaOH solution needed to reach the equivalence point is 34.41 milliliters. This is a practice question that i need help with. thank you
A chemistry student needs to standardize a fresh solution of sodium hydroxide. He carefully weighs out 150. mg of oxalic acid (H₂C₂O4), a diprotic acid that can be purchased inexpensively in high purity, and dissolves it in 250. mL of distilled water. The student then titrates the oxalic acid solution with his sodium hydroxide solution. When the titration reaches the equivalence point, the student finds he has used 77.1 mL of sodium hydroxide solution. Calculate the molarity of the student's sodium hydroxide solution. Round your answer to 3 significant digits. x10 M X 5 ?