24. The rigid pipe BC shown is supported by a pin at C and an A- 36 guy wire AB (E = 200 GPa). The wire has a diameter of 8 mm. Determine the load P (kN) if the end B displaced 5.2 mm to the right. H = 3.5 m, 0 = 60°. A. 4.25 В. 6.30 %3D С. 5.60 D. 3.23

Q: : the components of the 100 lb force are B. l00 A 60 30

A: Given data: Magnitude of the force = 100 lb Need to determine the components of the force along A…

Q: " 12 13 30° F₂= 200 N 5 F3 = 260 N the magnitude of the resultant force acting on the bracket is to…

A: Write the algebraic sum of forces in x-direction.…

Q: Using the Cartesian coordinate system, determine the absolute value of the distance y (in mm) from…

A: GIVEN DATA A COMPOSITE FIG GIVEN WE HAVE TO CALCULATE Y COORDINATE OF FIG

Q: draw it top and side sectional view

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: d the resultant and its orientation.

A: given

Q: Rotate the objects shown below by the indicated amount. Sketch the result in the space provided.…

A: Find Rotate the object about the given axis.

Q: TS DIAGRAM

A:

Q: -26-ト-26→ -3b 26 ---x

A:

Q: 1/3 sqrt(3) s3

A:

Q: Draw the aligned sectional view of the following solid

A: According to the given data, there are two projection views. We need to find The sectional view as…

Q: Rotate the objects shown below by the indicated amount. Sketch the result in the space provided.…

A: the solution is provided in the picture attached below.

Q: '. Oetermine the resultant OF the given vec fors ond the angle from the positive x- axis. vse Ony…

A: Given Data⇒ F1=500 N F2=300 N

Q: В |C O2 4 D 3 A E (201 5 F D 6 H at c I G Needle

A:

Q: For the objects shown below sketch the object in the space provided after rotating it about the axis…

A: Find Rotate the object about the given axis.

Q: Draw the three projection in sheet

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Using the Cartesian coordinate system, determine the absolute value of the distance x (in mm) from…

A:

Q: Solidworks MMGS units

A: Find Draw the given object in Solidworks. Unit: MMGS

Q: Draw the top view, side view, and front view of the figure below.

A: The required Front view , Top view and Side are drawn using third angle method of projection.

Q: Resolve the force F, into components acting along the u and axes and determine the magnitades of the…

A:

Q: M 50 10 60 M. 10 10 50

A: Let’s divide the section into three different sections as shown – Calculating area of the different…

Q: Q1. Force F = {270i + 450j –140k} N and it passes point B. The coordinates of the points are: A (21,…

A: Given: The force acting, F = (270i+450j-140k) N The distance between O and B, OB = 21 cm The…

Q: O find the root of the oquation -37/2 2t e . tant (3)

A: According t the question, f(t)=e2t. tant-e-3π2on differntiating this equation with respect to…

Q: The compressor is used to increase the flow energy of the gas Select one: True O False

A: Compressor is a mechanical device which used to increase the pressure of a gas in exchange of…

Q: Create a free hand oblique drawing of the three objects

A:

Q: ?Find the centeroid of the shaded area shown in fig 80 30 60 90 -20- 30 Dimensions in mm

A:

Q: 20 mm Determine the location y of the centroid C of the beam's cross-sectional area. Then compute…

A:

Q: When an object has multiple lines of symmetry, its centroid is not located at the intersection of…

A: Answer - False

Q: F 8 00 SKETCH THE APPROPRIATE AUXILIARY VIEW. 195

A: Draw Auxiliary view.

Q: Using the figure, find the magnitude of the resultant force. Numbers in picture are: Orange: 236 Ib…

A:

Q: 1. Draw top, front and right side views of the bracket as shown in Fig.

A: Required Front view, Top view and Right hand side view are drawn using third angle method of…

Q: y (x- 6y)dx - x (2x - gy) dy = 0; x =1 , y = 1

A:

Q: express this in cosine form

A: Giveny=-10sinωt+120

Q: O Determine the resultant CR) and its direction o ? 10ON 200 N 360 NO9

A: For the above given diagram the angle for the force of 200N is not givenSo assuming it as 60°As per…

Q: Q1. The force acting on the gear tooth is F = 20 N. Resolve this force into two components acting…

A:

Q: Ex2 of the bent bar. Determine the moment of P about point B and about point A. The 30-N force P is…

A: Need to determine moment about B

Q: Draw the three Views and a section elevation:

A: Required all three views Elevation, Right Hand Side View, Plan and Sectional Elevation are drawn…

Q: Which corners would be visible from the FRONT orthographic view of this image. Select all that…

A: Front view will be like

Q: (The direction of the front view is given) According to the dimensions, draw the three views. R10 10…

A: given figure

Q: lao N A Sm

A: The given system of force is as shown below, Resolving the force into two component,…

Q: what is the size of the circle (

A: The object is put in the first quadrant in the first angle projection. The item is at the top of…

Q: 8.07 60 45

A: 3D view

Q: Can you solve the force applied in x,y, and z in the image?

A: