24. (a) Derive the Boolean expression for the gate shown in Figure Q4. Using that expression or otherwise produce a Truth Table for this circuit. Finally, determine what equivalent logic gate this circuit would produce. NAND NAND NAND Figure Q4

24. (a) Derive the Boolean expression for the gate shown in Figure Q4. Using that expression or otherwise produce a Truth Table for this circuit. Finally, determine what equivalent logic gate this circuit would produce. NAND NAND NAND Figure Q4

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Using appropriate diagrams, explain how a combination of transistors and resistors would be used to construct an OR logic gate to control the flow of electrons inside an integrated circuit. please show mw how to do the digram
Problem #2: Apply the input waveforms A, B and C of the figure below to a NOR gate and draw the output waveform. A B C
Below is an example of an NMOS logic circuit. For all of the MOSFETs in the circuit below, assume V = 1 V and k = 50 mA/V². th W R₂ = 5600 PEETHIPPIN R₁ - 4700 M3 M₁ M. 0 a. Indicate and verify the state of each MOSFET and V for the following input combinations. Fill-out the table below for each assumed state of the MOSFET for every input combination. Use R approximation for linear operation and three significant ds(on) figures for the voltages. 오 Ao SV why
5) below is the accuracy table showing the output values for two separate binary number entries (W and Y) with a length of two bits. Get the simplest form of output functions with the Karnaugh diagram. Draw a logic diagram of the circuit that performs the function of these functions.Describe in detail which functions a, b and C perform for 2-bit binary numbers in the input.
The diagram shows a transistor used to interface a logic gate to a lamp for it to be fully lit. Resistance of lamp=80 ohms 9Vo Signal from logic gate Ovo R Logic gate Output 0.2V 3.3V IB V₁ Lamp a) The logic gate outputs 0.3 for logic 0,and 3.3V for logic 1. Complete the table below to show the effect of these signals on the transistor and lamp by: i) Adding the correct voltages to the V1 column ii)writing either 'Off' or On to show the state of the lamp V1(V) same as VB When filly lit the, the lamp passes a current of 100mA. The transistor has a current gain, beta ẞ of 60 b)Calculate the base current, IB. c)Using KVL find the voltage drop across R. Sate of lamp
a) A standard TTL inverter gate is shown in the figure. The supply voltage is 5V. Calculate the output voltage for both logic low and logic high input cases assuming input voltages respectively as 0.11V and 4.2V. Br= 130; BR = 0.24. You can make approximations when needed. Br = IcIs active region; BR = IE/ls inverse active region b) Assume you connect a resistor of 1.8K to the output of the circuit when the output is at logic high. What will be the change in the output voltage? 1302 R3 1.6k2 R, 4k2 Input o T, Output T, V, V. IkQ R,
Write the Boolean function of the gate circuit that makes the sequence counter (SC) zero. Draw the circuit diagram of the gates and show how the SC is connected to the INR and CLR inputs. (The number of gates should be minimal.)
Consider a digital logic circuit with two diodes as shownin figure 1. The diodes D1 and D2 are ideal (i.e. Vy = 0). 12 D ov, out 10 D2 5V 50kO Figure 1 A digital logic circuit with two ideal diodes A. Complete the equivalent circuit below and determine the output voltage vout oV and v, = 5V. Verify the conduction states of diodes by finding the current through D, and the voltage across D, when vị = Note that the output voltage is the same when v, = 5V and v, = 0V. 12 D out 12 D2 5V 50k2 Complete the equivalent circuit below and determine the output voltage vout when vị = v2 = В. 5V. 1Ω D Qut 10 5V 50k2 B.
Q4. (a) Switches arranged in the following figure, act like what type of logic gate? (b) Given a NAND gate and inverters, draw how you would produce an OR Function? (c) Given an AND gate and inverters, draw how you would produce a NOR function?
4. How to use the PLL circuit and the logic circuit to comprise a doubler frequency circuit?
Question 1 Here again, is our diagram of the half-adder from the previous page. Copy this half-adder to your paper. Then trace through the circuit and label the output wire for each gate. As an example, the output wire for the OR gate is labeled for you. P Q OR AND PVQ NOT AND sum -carry
Assume Vth = 1V and k = 50mA/V2. Given the schematic below, do the following: 1) Indicate and verify the state of each MOSFET and ?0 for the following input combinations. Fill-out the table below for each assumed state of the MOSFET for every input combination. Use ?ds,on approximation for linear operation. 2) Determine what kind of logic circuit is implemented in the circuit.