in. 25 in. 30 in.

Q: Find the centroid along y – axis of the shaded area. y - axis = mm. 14 70 -35--35–| Dimensions in mm

A:

Q: the Centroid of the Shaded Area

A: Draw the diagram

Q: Determine the x- and y-coordinates of the centroid of the shaded area. - 65 -180- 65 105 Dimensions…

A: To find centroid

Q: Determine location of neutral axis

A: Given data : Consider upper flange portion (A1)=100×20=2000 mm2Consider  web portion…

Q: A hexagonal prism of base edge 25 mm and height 50 mm is resting centrally on top of a rectangular…

A: The isometric drawing or isometric projection is projecting the object or structure in three…

Q: Determine the y-coordinate of the centroid of the shaded area. y 0.39h 62° 62° Answer:

A: Determine the y-coordinate of the centroid of the shaded area.

Q: W В 20 k 20 ft A 20 ft - 15 ft -

A: Given, w=1.25K/ft

Q: Q₂-Calculate the vertical movement for points A, B and C t 3.5м t A Steel Wire D = 35 mm E = 2×10" N…

A: Given Span10 mLoad 35 kNDiameter 35 mmElasticity modulus 2×104 N/mm2To find out Deflections

Q: Draw the shear force and bending moment diagrams and sketch the qualitative deflected shape.

A: The figure given in the question are as follows: w=1.5 klf

Q: Determine the y-coordinate of the centroid of the shaded area. y h 0.35h / 70°y 70° Answer: ỹ =

A:

Q: (1)Draw the sectional view from the front (section from A-A). (2)Draw the top view. (3)Draw the side…

A:

Q: Calculate the y-coordinate of the centroid of the shaded area. 52 mm 23-23- mm I I Answer: y = i mm…

A:

Q: Determine the y-coordinate (y-bar) of the centroid of the shaded area. (Use 3 decimal places) P=136…

A:

Q: Determine the x- and y-coordinates of the centroid of the shaded area. Input values only without…

A:

Q: Determine the y-coordinate of the centroid of the shaded area. y 0.25h 68° 68° --x Answer:ỹ = i

A:

Q: Kindly explain the process.

A:

Q: Determine the coordinates of the centroid of the shaded area. 25 60 50 25 180 65 55 45 Dimensions in…

A:

Q: Add 1 cm and 1 m A. 50 cm B. 101 cm C. 250 m D. 150 m

A: Given data : 1 cm , 1m Since , we know that : 1m = 100cm

Q: Determine the y-coordinate of the centroid of the shaded area. h 0.37h 70° Answer: y = i y I I / 70°…

A:

Q: Determine the y-coordinate of the centroid of the shaded area

A:

Q: Find the centroid and moment of inertia of the cross-section 275 mm Ref. Origin 50 mm 75 mm 50 mm…

A:

Q: SITUATION: Refer to Figure below. Point loads of magnitude 500 KN, 750 KN, 800 KN, and 1000 KN act…

A:

Q: Determine the coordinates of the centroid of the shaded area. y 30 E 55 -70 30 60 60 I 50 -x 195…

A:

Q: 1- Locate the centroid of the area ABC. For the shaded area x= y = x = y = For the perimeter A 240mm…

A: Since the given figure is symmetrical about the y-axis.Therefore, the centroid will be;Compute the…

Q: A two-dimensional two-dimensional normal to the plate. This causes the jet to split into two streams…

A: given- angle of strike=30o2 -D water jet

Q: A beam of circular cross section is 3000 mm long and is attached at each end to supports which allow…

A: L = Length of beam = 3000 mm = 3 mP = Offset load = 40000 N = 40 KNσy = Yield stress = 145 N/mm2

Q: Calculate uniform load W that the cantilever beam can carry having a length of 3m. The section of…

A: Given: Span. L = 3 m fc = 25 MPa fy = 276 MPa Tension reinforcements, 5-#28 mm h = 650 mm hollow…

Q: Determine the y-coordinate of the centroid of the shaded area. T h 0.35h Answer: y = y 68 68° tel x…

A: Given A shaded area Required  Y-coordinate of the area

Q: 351.6 meters x 0.0545 meter

A: Solution; We have a policy that we have to provide you answer in the second step.

Q: -r = 100 mm 50 mm

A:

Q: convert -0.009 °F/ft to °C/100m. Please provide the full dimensional analysis

A:

Q: Find centroid relative to x and y axes

A: The following figure shows the given shape.

Q: Find the area of the entranceway window shown. Express the area in squaremeters.

A: To find:- area

Length and Length related Variables

Length can de defined as the measurement or extent of physical quantities or objects from one terminal to another terminal. Stone age humans used finger length, step length, and so on to measure the size or displacement of an object. Nowadays, depending on how precise the measurement requires to be and the object’s size is measured, we use measuring devices for measurements like rulers and steel tape. Most people have used a ruler or tape measure to measure a particular distance or the size of an object. For more precise measurements of tiny objects, the development of measurement tools such as the Vernier caliper, which permits us to measure dimensions within 1/1000 of an inch. In the last few decades, electronic distance measuring instruments (EDMI) have been implemented that permit us to measure distances from a few feet to many miles with reasonable accuracy.