21)What are actor c to

Q: For the body shown. If point P3 is the center of mass for rod part P1-P2, and point P4 is the center…

A: A moment of inertia is a mass of the body when a body is rotating on an axis. The moment of inertia…

Q: The lightest 6 percent of the bowling balls made are discarded due to the possibility of defects. A…

A:

Q: If block B is moving downwards with a speed of 2 m/s at the instant shown, Determine the speed of…

A:

Q: A car's engine is producing 93 ft-lb of torque and is in a gear that gives an overall gear reduction…

A:

Q: 2) A car travels along a circular road with aradius of curvature of 75 m, and velocity of 10 m/s.…

A: Given Acceleration at 15 m  can be determined as

Q: A cold air-standard Otto cycle has a compression ratio of 12 and the temperature and pressure at the…

A: as per the guidelines i have to solve only 3 subpart of your question, kindly post remaining part in…

Q: 1. A 15 kg box frame is sliding down a 20° incline plane with a 10 kg steel sphere suspended inside…

A:

Q: The 500MB jet airliner has three engines. each of which produces a nearly constant thrust of 250 kN…

A:

Q: Please do not submit previous solution i need the correct answer. Read the question carefully

A: Step 1: Step 2: Step 3: Step 4:

Q: 1 F= 70,000 lbs. 60- 1 F= 70,000 lbs. STAINLESS STEEL angle A = Will the rod fail? (Yes/No) YIELD…

A: Since it is not clearly visible except L=60" the dimensions are in inches or feet, so it is taken in…

Q: A fluid jet (p = 1,445 ) has a diameter of 76 mm and a velocity of 2 m/s. The m3 jet impacts a…

A:

Q: Question 1 A band brake (Figure 1) uses a 100 mm wide woven lining having design values of f = 0.3…

A: Givenf=0.3Pmax=0.7 MPaN=150 rpmw=100mm

Q: A three-legged tube is filled with oil (SG =0.88). As shown, the surfaces of oil in all legs are at…

A: Maximum angular velocity:

Q: a stone is thrown vertically from a 100 ft tower with initial velocity = 50 ft/ sec ,at the %3D same…

A:

Q: An AISI 1010 HR steel beam that has a diameter of 20 mm supports non-rotating cyclic bending load at…

A:

Q: Q13) Cars A and B are travelling around the circular race track. At the instant shown. A has a speed…

A:

Q: Analysis and conclusion from the given picture.

A: Answer given below:

Q: Flat belts are the simple system for power transmission. They can deliver high power to moderate…

A: This question is related to the flat belts. The expression of angle of contact of the pulley.…

Q: A steel disk with a 150 mm outer diameter is to be press fit to a hollow steel tube whose outer…

A:

Q: It is observed that the skier leaves the ramp A at an angle OA = 30 degrees with the horizontal and…

A: Given data  VA = 21.8 m/s θA = 30 degrees g = 9.81 m/s2 To determine  a) Time of flight (tA-B) b)…

Q: The mass of the represented system is released under the initial conditions xo 0.1m and xo -5m/s…

A: Given : x0 = 0.1 m v0 = - 5 m/s To find: Response graph Time at x = -0.05 m

Q: The 4-kg collar is attached to a spring that has an unstretched length of 2m and a stiffness k=10.1…

A: Given: The mass of the collar is, m=4 kg. The unstretched length of the spring is, l=2 m. The…

Q: A100 kg boy starts from rest at the bottom A of a 10-percent incline and increases his sneed at a…

A:

Q: Design the yoke and rod connection as shown on the figure to withstand a load of 14 KN. If the…

A:

Q: Sketch the bending moment diagram of the frame bearing vertical uniform load (no calculation needed,…

A: given; draw the bending moment diagram;

Q: Find the area of the shaded region. The area of the shaded region is ▶ 9 ft 8 ft A 8 ft ... 18 ft…

A:

Q: Two and a half cubic meters of lumber is being dried at 70°C dry bulb temperature and 50°C wet bulb…

A:

Q: I would like a more detailed explanation on each step to reach the final answer

A: Understand that the free end of the pipe will tend to move from point A to point B (when the force…

Q: 2. In the figure shown, a liquid is pumped from reservoir A to tank B by a 12 hp pump having an…

A:

Q: For the body shown. At the instant shown, point B moves in straight line in y positive directi with…

A: There are two types of accelerations that are acting on a circular surface. One type of acceleration…

Q: Ruestion 3 The combined pulleys in Figure 3 use friction to transmit motion. If block A has a linear…

A:

Theory and Design for Mechanical Measurements

Measurement is a term that refers to analyzing a manufactured component regarding the degree of accuracy for dimensions, tolerances, geometric profile, roundness, flatness, smoothness, etc. Measurement always involves comparing the manufactured component or the prototype with a standard specimen whose dimensions and other parameters are assumed to be perfect and do not undergo changes with respect to time.Precisely in mechanical engineering the branch that deals with the application of scientific principles for measurements is known as metrology. The domain of metrology in general deals with various measurements like mechanical, chemical, thermodynamic, physical, and biological measurements. In mechanical engineering, the measurements are limited to mechanical specific such as length, mass, surface profile, flatness, roundness, viscosity, heat transfer, etc.

Basic principles of engineering metrology

Metrology is described as the science of measurement, precision, and accuracy. In other words, it is a method of measurement based on units and predefined standards.