21. The sequences of voltage levels shown in Figure 13-72 are applied to the summing amplifier and the indicated output is observed. First, determine if this output is correct. If it is not correct, determine the fault. +3 V +2 V +1.5 V VIN +1 V OV +2 V +1.5 V +I V R4 VIN2 R -IV H+1.5 V VINIO VIN3 O V R2 0.5 V VIN OW o VOUT -3 V +3 V R3 VINI OW VOUT All resistors are 10 kf2. -I V -I V -2 V -4.5 V

21. The sequences of voltage levels shown in Figure 13-72 are applied to the summing amplifier and the indicated output is observed. First, determine if this output is correct. If it is not correct, determine the fault. +3 V +2 V +1.5 V VIN +1 V OV +2 V +1.5 V +I V R4 VIN2 R -IV H+1.5 V VINIO VIN3 O V R2 0.5 V VIN OW o VOUT -3 V +3 V R3 VINI OW VOUT All resistors are 10 kf2. -I V -I V -2 V -4.5 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Number 23
Q.No.4: A flash type analog to digital converter as shown in figure (b). The input is Vin = 5V. Find the digital output. 10 4.0 VDC Vin 1 k2- X2 Bị (MSB) 2k2 Decoder X1 Chip Bo (LSB) 2 k2- Xo 1 k2 Figure (a) Analog to Digital Converter
amplifirs
Does output voltage for a inverted op amp Voup= +Vsat
Question 7 Select the voltage of the power source connected to an opAmp, given the following input and output signals: 20V -20V 15V -15V O Vcc= VII = 15V Vcc= VII = 10V Vcc= -VII = 20V O Vcc= -VII = 15V Input Signal Output Signal
R1 R2 Vo Vin Determine the output voltage, Vo in mV. R1 =13931ohm, R2-5112ohm and peak input voltage of Vin=14mV
In the figure, the parameters of both transistors Vo = 0.6 V RBB 10kohm Bdc 100 VCC 9V and T2 operating point Ic2 1mA VcE 5V Calculate the values of the resistors R1 and R2 R R
Questions 1 The operational amplifier (op-amp) in Figure 1 is an ideal op-amp with maximum output voltage, vo(max) is +12 V and the minimum output voltage, vo(min) is -12 V. A sine wave with +5V peak-to-peak voltage is applied as the input, vin as shown. R. RE Voltage (V) GND 10- Vin R2 Vin Vo Time 0.5 -5 -10- 1 1.5 (ms) GND Figure 1 For each of the following conditions, derive or explain the relationship between output voltage, vo and input voltage, Vin, and then draw the input and output voltage waveforms on same graph. Label the x-axis, y-axis, peak voltages and units. a) R1 = R2 = R3 = 10 kQ and RF = 3R1. b) R2 = R3 = 10 kn, RF = 3R2 and R1 is broken (open circuit). c) R1 = R2 = R3 = 1O kN and Re is broken (open circuit). d) R; = R2 = 10 kQ, RF = 3R1, R3 is broken (open circuit) and the op-amp's inverting and non-inverting terminals are accidently interchanged where node 'x' is connected to the non-inverting input while node 'y' is connected to the inverting input of the op-amp.
Show all steps please
How long does it take the output voltage of an op-amp to go from -15 V to +15 V, if the slew rate is 0.5 V /μs?
Hi, I need your help on the following question:Design an adapter circuit that has the input 120 rms 60 Hz and the output 12V 1A
Question 11 In a step-up/step-down converter, Vin=12V, Vioad=15V (regulated), Itoad=250mA, Lmin = 150µH, C = 470µF and fs=20kHz. Calculate the peak-to-peak ripple of the load voltage.