20,000 Ω 5000 Ω +60 V - 2 V 1V -60 V Ως 9Ω 12Ω νo

Q: Draw the outputs of the circuits to scale according to the input signal.

A: We have to draw the output waveforms for following input signal and circuits:

Q: 6. Draw the output Q for JK F.F if the input as below ск Об Ь J K- С PA

A: Draw the output waveform of JK flip flop if input as given below : Let initially output Q=0. In…

Q: hat about /Q, this is not mentioned in the state diagram

A: It is given that:

Q: e transfer ratio

A:

Q: If the input is current and the output is voltage, Which of the passive component performs…

A: Active Element: The element which delivers electrical energy is called as active element. Ex-…

Q: Qz Find the output response if the frequensy vespunse of the system is HCw)= for the fullowing 2+jw…

A: the frequency response of the system is given.  If the input is step input then find the output…

Q: (b) i. Explain the three classifications of transducers based on energy conversion UTM with block…

A: You have asked multiple independent questions. We are authorized to answer one question at a time.…

Q: What is FR4?

A: Answer: to find about FR-4

Q: 2 kn 16- 3. -16아 For the Given and input waveform determined the output waveform a) b) 16 C) 12 d)

A: Assume the diode is ideal, hence, the voltage drop across the diode will be zero. In the positive…

Q: Determine the gain ang phase shift of the given oscillator

A: We have given the problem Determine the gain ang phase shift of the given oscillator

Q: In PAM, an analog signal is sampled at equal intervals, with the resu Select one: True False

A: The above statement is false

Q: Figure Q.3 (a) R Q(next) Q(next) Action 1 1 Forbidden 1 1 Set 1 1 Reset 1 1 Q No change Consider Q…

A: Latch is asynchronous device. It is level triggered device. It check input and change output…

Q: 4. For an FET Colpitts oscillator as in the circuit and the following circuit values determine the…

A: In the following section, the oscillation frequency of the oscillator has been determined.

Q: The BW of an amplifier may be increased by

A: The bandwidth can be increased by negative feedback, where gain varies with change in frequency to…

Q: Skelch the vesponce : for aunit step change in Tics) O without coutoller coPen Ioop) Q with…

A: The response is determined for with controller and without controller

Q: Q8/ What is the difference between SWR and VSWR

A: For the above given concepts we need to define difference between them.

Q: Suppose you have an input current of Ib = 10 μA and an output current of Ic = 1mA, determine the…

A: Amplifying factor is the ratio between collector current and base current.  Given collector current…

Q: In an Encoder circuit when n =7 and for input value 001000, the output value is: 000 010 O 011 O 101

A: Given: The input is 001000

Q: Determine Vo for each of the output network shown. +8 V 22 ka+ (a) (b)

A: In the question, provide the output waveform for Vo. Label Vin graphs and Vo graphs completely…

Q: The behavior of oscillator is described by Olong periods of dissipation followed by short impulses…

A: Oscillators are nothing but the device which works on the principle of oscillations.These are used…

Q: FIR has may have one zero Select one: O True O False

A: Need to find true false

Q: If you have a measurement signal with zero drift, then which of the following operations you need to…

A: Drift: Drift means variation in the output of an instrument from the desired value from a given…

Q: The table below shows some performance parameters of a certain power transformer. Full-load voltage…

A: In this question,  Choose the correct options What is power factor to become zero voltage…

Q: Find the output of the following circuit 33 kf2 10 kf) Vout

A:

Q: 2. Show the step-by-step solution for each half cycle. Sketch the output voltage waveform for the…

A:

Q: The sampler is a linear device used to transform a continuous signal to a discrete one. O True O…

A: A statement is given, we need to comment on the statement, that whether it is true or false.

Q: Voltage follower

A: Voltage follower is an Opamp circuit whose output voltage straight away follows the input voltage.…

Q: Q#5 Draw for a full-wave fully-controlled bridge Rectifier with highly inductive load. i- Circuit…

A: In the given questions we need to design the circuit of signals phase full wave rectifier and it's…

Q: The ratio of IC to IE is equal to Select one: O a. aDC O b. either BDC/ (BDC + 1) or aDC, but not…

A: Given: The ratio if IC to IE is equal to ____.

Q: Consider the following figure. Represent the discrete samples into their corresponding hex values.…

A: According to the question, we need to draw the analog signal based on the given discrete samples as…

Q: // find transfer function for the Electric Circuit below Ri t Uit) (re) CI F

A: The transfer function is defined as the ratio of output to input at zero initial conditions. Convert…

Q: What is the difference between the two signals? Is there any distortion in the signals? If yes,…

A: Noise is some unwanted signal added to the original signal. It changes the shape and size of…

Q: A digital signal is a composite analog signal with a. finite bandwidth b. Infinite bandwidth c. zero…

A: In this question we will write about digital signal and analog signal composition....

Q: Q)design an op-amp cct to produce an output voltae as shown from input signal vin = sin(2nt) vo T/6…

A: The op-amp to produce the output voltage:

Q: QLFind the resistance for terminal 2.

A: To find the equivalent resistance of a complex circuit, it is important to convert complex circuits…

Q: The sinusoidal current waveform having the R.M.S value of 10 A, then the maximum value is

A: Given :    Note :  It is the kind notice that it according to the guidelines of the company we…

Q: 13. CALCULATE THE OUTPUT VOLTAGE OF 12VRMS 50Hz F1 a) 3.86 V dc b) 5.4 V dc c) 7.632 V dc d) 10.8 V…

A:

Q: TWO Signal ane FIND Yin)=x(n) * hlu) 11

A:

Q: In an op-amp comparator, when the input voltage crosses zero, the voltage output will be always…

A: In comparator circuit of opamp, output will be either +Vsat  or -Vsat. it will never be 0V.