20. A uniform ladder 18.7 ft long is leaning against a frictionless wall at an angle of 45.5° above the horizontal. The weight of the ladder is 32.0 pounds. A 68.0 Ib boy climbs 5.59 ft up the ladder. Calculate the coefficient of static friction that acts between the ladder and the ground to keep the ladder stable. (Pro-Tip: do not waste time converting to SI units as they will cancel appropriately; use the force and distance values given.) a. 0.364 b. 0.370 c. 0.163 d. 0.0425 e. 0.357

20. A uniform ladder 18.7 ft long is leaning against a frictionless wall at an angle of 45.5° above the horizontal. The weight of the ladder is 32.0 pounds. A 68.0 Ib boy climbs 5.59 ft up the ladder. Calculate the coefficient of static friction that acts between the ladder and the ground to keep the ladder stable. (Pro-Tip: do not waste time converting to SI units as they will cancel appropriately; use the force and distance values given.) a. 0.364 b. 0.370 c. 0.163 d. 0.0425 e. 0.357

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Chapter 12, Problem 028 GO In the figure, suppose the length L of the uniform bar is 2.7 m and its weight is 220 N. Also, let the block's weight W = 280 N and the angle 0 = 27°. The wire can withstand a maximum tension of 440 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A? com A (a) Number Units (b) Number Units (c) Number Units Click if you would like to Show Work for this question: Open Show Work
A woman whose weight is 336 N is poised at the right end of a diving board with a length of 5.04 m. The board has negligible weight and is bolted down at the left end while being supported 3.59 m away by a fulcrum. Find force that the fulcrum exerts in the board. Note: Express your answer in whole numbers. No unit is required for the final answer. Bolt Fulcrum (a) Axis (2 = 1.40 m Fi lw = 3.90 m (b) Free-body diagram of the diving board Round your answer to 0 decimal places.
Needs Complete typed solution with 100 % accuracy.
Please answer clearly.
A uniform, 3.0 m, 1150 kg beam is hinged to a wall and supported by a thin cable attached 2.0 m from the free end of the beam (Figure 1). The beam is supported at an angle of 30.0 above the horizontal. Figure 40.0⁰ 30.0⁰ 1 of 1 2.0 m ▼ Find the tension in the cable. Express your answer to three significant figures and include the appropriate units. T= Submit Value Part C 1 O Units www A Previous Answers Request Answer X Incorrect; Try Again; 9 attempts remaining Units input for part B ? How hard does the beam push inward on the wall? That is, find only the horizontal component of the force. Express your answer to three significant figures and include the appropriate units. BOL 11 ?
PROBLEM 1: Determine the mass of the heaviest uniform bar that can be supported in the position shown if the breaking strength of the horizontal cable attached at C is T kN. Neglect friction. A 4 B Given: x = 1.2 m O = 20° T = 15 kN W = kN (round off to 2 decimal places) 3.
A 25-ft crane supported at its lower end by a pin is elevated by a horizontal cable. A 250-lb load is suspended through the cable. The center of gravity of the crane is 10 ft from the pin, and the crane weighs 200 lb. Hint: You don't have to convert the unit since they cancel out on both sides. 25. Find the tension in the cable. T $25016 26. Find the total force acting on the pin. y 27. Find the direction of the force acting on the pin, o = ? 60⁰° W(2001b)
A uniform drawbridge must be held at a 38o angle above the horizontal to allow ships to pass underneath. The drawbridge weights 55000 N and is 15.0 m long. A cable is connected 3.5 m from the hinge where the bridge pivots (measured along the bridge) and pulls horizontally on the bridge to hold it in place. What is the tension in the cable? Find the magnitude and direction of the force the hinge exerts on the bridge. If the cable suddenly breaks, what is the magnitude of the angular acceleration of the drawbridge just after the cable breaks? What is the angular speed of the drawbridge as it becomes horizontal? What is the velocity of the drawbridge, just before it “hits” (i.e. goes horizontal)?
Please help me
A shelf bracket is mounted on a vertical wall by a single screw. S S2 S1 Neglecting the weight of the bracket, and if s = 6.4 cm, s1 the horizontal force component exerted on the bracket by the screw when a 95.2 N vertical force is applied as shown. Imagine that the bracket is slightly loose. 5.4 cm and s2 = 2.2 cm, find =
A weightless strut, hinged to a wall, is used to support a 200.0 N block as shown. The horizontal component of the force of the hinge on the strut is: 3m Cable Beam com 2m Rope Hinge 300.00 N 375.00 N 330.00 N None of these 270.00 N ос
Structural member AB is to be supported by a strut CD. Determine the smallest length CD may have, and specify where D must be located for a strut of this length to be used. Take x= 120 mm. 60 mm D. y 20 mm E The smallest length CD may have is mm. The coordinates of point Dare ( and Imm.