Read the question carefully and give me right solution according to the question.Answer also given A riveted lap joint is shown in thefigure. The rivets used are A502,Grade 2, hot-driven with diameter of16 mm. The steel is ASTM A501, 200mm wide and 10 mm thick.Determine the value of P in allpossible modes of failure and the safevalue of P that the connection can10 mmresist. Fy = 248 MPa, Fu = 400 MPa, Fv= 152 MPa, Fp=1.2Fu. Use 1.6 mm10 mmallowance for the hole diameter.Ans. 152.8 KN

The above given system of rivets can be subjected to failure by 5 different criterions which are as…

Answered: 20 m A riveted lap joint is shown in…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
I need these three parts answered, if you are unable to answer all three parts please leave it for another tutor to answer, thank you.
HANDWRITTEN. answer 4 5 6 then box the final answers
A sprinter practicing for the 200-m dash accelerates uniformly from rest at A and reaches a top speed of 36 km/h at the 76-m mark. He then maintains this speed for the next 61 meters before uniformly slowing to a final speed of 31 km/h at the finish line. Determine the maximum horizontal acceleration which the sprinter experiences during the run. Where does this maximum acceleration value occur? Part 1 Answers: (a) al- Finish line Calculate (a) the magnitude of the tangential acceleration near start of the race and (b) the magnitude of the tangential acceleration near the end of the race. (b) lal- i 0.658 i 0.205 m/s² 39.9 m m/s² A Save for Later Last saved 12 minutes ago. Saved work will be auto-submitted on the due date. Auto- submission can take up to 10 minutes. Attempts: 0 of 3 used Submit Answer Part 2 The parts of this question must be completed in order. This part will be available when you complete the part above.
i need the answer quickly
Solve it quickly please
Hi, Could you please help with this question, if you need to take more credits then please feel free. showing working out if possible too please, Thank you
Question 20 Use basic drawing instruments (pencil, scale, protractor, compass, etc). The Front View of a line AB measures 65 mm and makes an angle of 45° with xy. A is in the H.P. and 15 mm in front of the V.P. The line is inclined at 30° to the V.P. Draw the projections of AB and find its true length and inclination with the H.P.
Q/Answer the following blanks 1. The chemical formula of the maximum copper ore is ...: 2. The chemical formula of the minimum copper ore is .: 3. The copper ore which contain a percentage ratio of iron is .: 4. The pure copper is and ductile and soft with color of .. 5. double fluoride of aluminium and sodium called as 6. the copper-zinc alloys are named as. ***........ 7. The softest and heaviest of all the common metals is. . 8. The zinc ore which is included percentage ratio of Sulphur is 9. Shape, color, and size are properties. 10. The nonferrous metal which is high density and easy workability is ............ 11. In Rockwell test, the major load is applied for a specified time . .beyond zero 12. The of the indent .is a function of the test force divided by the curved surface area 13. The charge is fed through a charging door and is heated to . radiation of heat in open hearth. .mainly by 14. the metals flow and a relatively large permanent set takes place without a noticeable…
Given the table of results find the following. Give answers in KW. Please show all working out Rate of heat transfer to evaporator from the chilled water Rate of heat transfer from condenser to the cooling water Rate of heat transfer to refrigerant in Evaporator using enthalpy values Rate of heat transfer from refrigerant in Condenser using enthalpy values Work input from the compressor to the refrigerant using enthalpy values
Can some one please help to solve this question following the directions and showing neat work and formulas. PLEASE AND THANK YOU!!!
Please show work for all these answers and a clear and short explantion of each one

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS