20 kN 15 kN/m 40 kN.m Q2) Draw the S.F.D and the B.M:D for the beam shown 2 m 2 m

Q: Determine the maximum value of b (lb/ft) if the roller at point A can only support upto 95 lb. The…

A:

Q: Problem-2 The tension in the guy wire is 2500 N. Determine: a) components Fx, Fy , Fz of the force…

A:

Q: Reduce the force and couple moment system shown in the figure to a single resultant force acting on…

A:

Q: 4. Draw the FBD of member DABC 12 in. 12 in. A 150 lb B ----- -3 ft -5 in D 5. Draw the FBD of…

A:

Q: For the beam and loading shown, determine the vertical reaction at B (lb) provided that a=175,…

A:

Q: For the beam and loading shown, determine the magnitude (lb) of the vertical reaction at A if P =…

A:

Q: 50 KN/m 120 KN.m B- 9m 4m

A: For solution refer below images.

Q: Q2. ~ 9=90(즌- A

A: We will solve this problem by double integration method  Consider any section XX from the end  A…

Q: supports the loadings shown. Determine the equivalent force acting on the beam and its point of…

A: The equivalent force acting on the beam and its point of application measured from point B.

Q: For the beam and loading shown, determine the vertical reaction at A (lb) provided that a=156,…

A: Answer:  RA=107.500 lbFor a step-by-step solution have a look through the attached pictures of the…

Q: Determine the magnitude of the moment (lb-in) due to the two couples shown if P=48 lb and Q=58 lb…

A: Magnitude is a term that describes the size or distance of something. We may link magnitude with the…

Q: 2. For the frame shown, a) Solve for the reaction at the roller support at A and the horizontal and…

A:

Q: Three concentrated live loads of 10 KN, 20 KN, and 36 KN are to cross a simple beam with a span of…

A: The given beam can be represented as  -

Q: Determine the magnitude of force (lb) in member BD if P = 170 lb, x = 15.8 in, y = 10.1 in, and z =…

A:

Q: Q2) Determine the reactions at support A. 8 kN/m -1.5 m- T 5 kN.m 1.5 m- 6 kN

A: We will compute the reaction force at the fixed end of the cantilever beam in this issue. The…

Q: termine the magnitude of force Q such that the resultant couple moment of the two couples acting on…

A: GivenP=585lb

Q: Q4) 200 cm X B 300 cm 227 cm 125 cm 75 cm Determine the force acting along the axis of each of the…

A: Mass of block, M=500 kg

Q: a lb/ft b lb/ft- A В c ft-

A: This numerical from strength of material portion. Used concept is  To convert the uniformly varying…

Q: shead fooce diagsam 15 KN 4-5 m 1-5m 1.5 m

A:

Q: The resultant of the three forces shown is R=200 kN. a) Determine the magnitude of the force AD. b)…

A: Given: R  = 200KN

Q: 20 kN 15 kN/m 40 kN.m Q2) Draw the S.F.D and the B.M:D for the beam shown A 2 m- 2 m

A:

Q: Q1/Determine magnitude of force at DA and GF members by using a) joint method b) section method C B…

A: For the solution refer below images.

Q: Q 2) Determine the centroid (ỹ) of the shaded area. 1m y%3Dx 1m

A:

Q: Q4) Determine the magnitude of the horizontal force F and the support reactions at pin A. If the…

A: Drawing FBD:

Q: Gg Three wires are connected at point D, which is located 18 in. below the T-shaped pipe support…

A: The weight of the cylinder is

Q: The magnitude of the moment of the force F=400 N about point O is equal to. 30 45 0.3 m 0.4 m Select…

A:

Q: In the assembly shown, sags of s and 1.5 s resulted when the two cylinders were suspended from the…

A: Given: spring constant for spring BD→KBD=134 Nm value of s=0.85 because initial length of the…

Q: 1. Determine the moment, in kN-m, at x = 5 m distance to the right of the left end of the beam. P1 =…

A: Correct answer: d) answer is not among the choices

Q: - 24 in.- D P 10 in. B C y

A:

Q: Determine the values of a and b so that the shown beam is in equilibrium when F = 1.5 kN and M = 2.5…

A:

Q: QI/ a) While steadily pushing the machine up on an incline surface, a person exerts 180 N force P as…

A:

Q: For the truss shown, a) find the load in member GH using the method of sections, and  b) indicate…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.