20 20 50 30 유 8

Q: SECTION +A DRAWN BY: Point AB А с D E F G H I J K L X O O <-5 <-5 -10 -10 2 6 6 3 3 O Coordinate Y O…

A:

Q: (Q1] Replace the system shown below by a single force at B and a couple. 700 N 30 450 N 300 N 60 BY…

A:

Q: f 20

A: To mark the exact design shown in the figure

Q: Draw the isometric view. The first photo is the given. The second one is the given dimensions 1st…

A: Given: Draw isometric view, from given orthographic projections.

Q: orthographic view (software drawn)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: 3- A sport man make a jump ,the vertical position of his center of gravity can be expressed as the…

A:

Q: zes/147167/take stion 1 O pts • What are the r and y components of a vector of length A that makes…

A: givenvector length =A

Q: provide Orthographic view

A: Question fig.

Q: Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please

A: we consider the angles for better understandingthank you

Q: :Coplanar force system means

A: The general definition of force: It is the capacity to do work.

Q: A particle is subjected to two forces F₁ -3.5-6.5-7.5k (N) and F2-8.5-5.5) -6.5k (N) The magnitude…

A:

Q: E-210GPA - A= Soomm しこ 2Smyyop A= 5mm Btles in Al ベ=2 ×Tシ

A:

Q: Q1/ The physical change in dimensions of the material and its state as a result of an increase in…

A: Thermal expansion is the tendency of matter to change in shape, volume, and area in response to…

Q: Write an equation for the lines that pass through (1/3 , 4) and has slope = 0. %3D

A: The equation of line is y=mx+c The given points are 13,4 and the slope is 0 Substitute values in the…

Q: acceleration (a ) can be determined as a= dx/dt a= dv/dx a= dv/dt a= dx/dv

A: Acceleration is the rate of change of velocity with respect to time . It has both magnitude and…

Q: 1.o. --O f₁ 0 f₁ x- 2" 0- fz

A: The sketch is shown below, as per the principles of ray diagram.

Q: 60 20 IS RID 40 90 65

A: the view shown below step 2

Q: Sketch the Orthographic and  auxiliary view

A:

Q: 300N 12 45 505 N Fig. A

A:

Q: Assume all lines are connected. Apply three constraints on the lines and the the sketch. (Indicate…

A: Given: To find: Apply 3 constraints

Q: Find the front, side, and top projection

A: Solution: The Front, Side and Top view are shown below:

Q: Draw the pictorial isometric view using the two given orthographic projections

A: Refer the below image for the required isometric view for the given orthographic views.

Q: Required: Draw the front projection, the left side projection, the horizontal projection

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: According to Pascal, pressure applied to a fluid O is transmitted unchanged throughout the fluid O…

A: GIVEN DATA-   A MCQ QUESTION GIVEN ABOYUT FLUID MECHANICS   WE HAVE TO TELL CORRECT ANSWER  CONCEPT…

Q: The vector quantities are the quantities that have magnitude only O direction only O magnitude and…

A: Vector quantities have magnitude as well as direction both. Example velocity, Force etc.

Q: Q/DRAW THE PROJECTIONS OF A SHAPE

A: According to the details provided in the question, we need to calculate projections of the object.

Q: what does that symbol mean, it looks like a "Cn"

A: Given: what does that symbol mean, it looks like a "Cn"

Q: determine Hhe magnitude of the FA= 8 KN resultont anel the odirection measurud from the horiZontal…

A: Given Data: FA=8 kN FB=6 kN

Q: Draw the frontsideant top view the Shape Shown

A: According to the details provided in the question, we need to Draw three projection views.

Q: POSSIB Observe Graph 1. Which line on Graph 1 represents the change in kinetic energy as the steel…

A: Basics of Energy conservation.

Q: Scaling. (a) Considering a spherical particle is moving in a of the particle decreases due to the…

A:

Q: Help!!!!!!!!

A: First angle projection:Front view is at the top of the horizontal axis.Top view at the bottom of the…

Q: DRAW OBLIQUE

A: OBLIQUE VIEWOblique drawings provide a quick way to sketch an object and represent the three…

Q: Find the moment of the force about point O 100 mm 20% F = 60 N

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.