2.51. A bar of thickness 1 in. has a symmetric step change in width from 2 in. to 1.5 in. through a fillet radius of 1/8 in., as shown in Figure P2.51. It is subjected to a bending moment of 4000 lb in. Find the maximum tensile stress at the change of section. radius 4000 lb in 4000 lb in 2 1,5 all dimensions in inches

2.51. A bar of thickness 1 in. has a symmetric step change in width from 2 in. to 1.5 in. through a fillet radius of 1/8 in., as shown in Figure P2.51. It is subjected to a bending moment of 4000 lb in. Find the maximum tensile stress at the change of section. radius 4000 lb in 4000 lb in 2 1,5 all dimensions in inches

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the value of stress Force 2.2 N Area=2 m2
1. A force P = 27 kN acts on a round bar with d = 50 mm, find the stress in KPa. 2. The piston rod of a steam engine is 70mm in radius and 400 mm long. The radiusof the piston is 200mm and the maximum steam pressure is 2 N/mm2. Find thecompression of the piston rod if the young's modulus for the material of the pistonrod is 250 kN/mm2.
Consider the figure below. If T1=3,500 lbs and T2 = 2,500lbs, fin the angle alpha made by T2 from the horizontal.
A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding. 24m
2.4. The stress at a point is defined by the components Oxr =0 MPa, Oyy= 100 MPa, Oxy = Oyx plane on which the maximum principal stress acts to the x-plane. %3D =-40 MPa. Find the principal stresses o1, 02 and the inclination of the
2. The stress at a point of a machine component are 200MPa tensile and 100MPa compressive. Using Mohr’s Circle method find the intensities of normal, shear and resultant stresses on a plane inclined at an angle of 300 with the tensile stress. Also find the magnitude of shear stress in the component.
100 kN 75 mm 50 mm 50 mm 75 mm 40 kN 30° 400 mm H K! Find stresses @ k.
Question # 1 Fig 2 shows an unstressed aluminum plate 2/4 inches thick. A circle of 9.5 inches diameter is scribed on it. Normal stresses of 15 ksi and 22 ksi, along x and y direction, are caused by forces acting in the plane of the plate. For Poisson's ratio 4 and modulus of elasticity 10 *10^6psi,then determine the following (a)change in the length of diameter AB (b)change in diameter CD (c)variation in the plate thickness (d)the volume change of the plate
1. A shaft 80 mm diameter transmits power at maximum shear stress of 63 MPa. Find the length of a 20mm wide key required to mount a pulley on the shaft so that the stress in the key does not exceed 42 MPa.
2.49. A bar of rectangular cross section 20 mm × 3 mm has a central hole of diameter 6 mm. Find the maximum tensile stress if the bar is subjected to a tensile force of 5 kN.
Calcuate Bending From Point A to Point B and Point A to Point C, Calcuate torsion From Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
2. The Principal stresses at a point across two perpendicular planes are 90MN/m² (tensile) and 40MN/m² (compressive). The shear stress across these planes is 25 MN/m² (counter clockwise). Find the normal, tangential and the resultant stress & its inclination on a plane making an angle of 35° with the plane of first stress.