2.51 Water, oil, and salt water fill a tube as shown in Fig. P2.51 Determine the pressure at point 1 (inside the closed tube).

Q: Convert the decimal number 35710 into its octal number equivalen

A: Steps Write the given decimal number. If the given decimal number is less than 8 the octal number…

Q: With the help of a neat free-hand sketch, explain how to construct the involute of a circle.

A: construct the involve of a circle.

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: 1. The . . tool is used to draw the cutting plane line arrowheads in AutoCAD .... a. spline fit b.…

A: 1)  d) polyline 2)  c) revolved 3)  b) partial 4)  b) half

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

A:

Q: Draw Front and Side and top with all dimensions please

A: Find Draw the front, side, and top of the object with dimensions.

Q: Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to…

A:

Q: can you please write it in a proper way?

A:

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the…

A: The chip compression ratio can be defined as the ratio of the chip thickness and uncut chip…

Q: FORTUNE FAVOURS THE BRAV

A: A week ago our little villa was invaded by fear-based oppressors. There was dread in the seniors.…

Q: Convert the decimal number 11510 into its octal number equivalent

A: Convert Decimal to Octal with Steps Write the given decimal number. If the given decimal number is…

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: short notes on any two types of chips formed during metal cutting operation

A: Metal cutting is defined as "the act of eliminating undesirable material from a block of metal in…

Q: Orthographics: Add missing lines and complete any missing views. Draw the isometric

A: The missing lines of the given views are shown below.

Q: A piece of 12-gauge sheet metal is 7⁄64 inch thick. A stack of sheet metal is171⁄2 inches thick. How…

A: Given12 guage sheet metal sheet thickness t=7/64 inchthickness of stacked sheets t2=171 2inches

Q: Write the types of keys and sketch freehand of them with dimensions and equations.

A: A key is a machine element that is fitted in the axial direction with the mating parts in pulleys…

Q: Can you show the work but written out please so I can see the steps better.

A:

Q: What type of lines can be used in a drawing to show that part of an object has been removed ?

A: Solution : There are two types of line which are used to show the removed part of an object : Break…

Q: In a lathe machine tool, when the cutting tool moves perpendicular to the axis of rotation of the…

A: True

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

A:

Q: Draw the and B A.F.D&S.F.D& B.M.D (KN.M

A: To draw axial ,shear and bending moment diagram

Q: 0 = 0° A

A:

Q: can you draw the FBD

A: There are four rivets in this problem. In ideal case load will be equally distributed. Each rivet…

Q: Draw the top view  front view  right side view  on graphing paper please. Put measurents if…

A: Required Front view, Top view and Right Hand Side view are drawn using First Angle Method of…

Q: TOP FRONT SIDE

A: GIVEN DATA ISOMETRIC VIEW GIVEN WE HAVE TO DRAW ORTHOGRAPHIC VIEWS OF GIVEN FIGURE

Q: Write the Column Formulas?

A: Types Critical load Both ends hinged π2EIl2 one end hinged other end fixed 2π2EIl2 both ends…

Q: 7. Using the drawing below as a reference, Change "101" refers to which feature on the drawing? A.…

A: according to the drawing

Q: What is an inflection point?

A: In solid mechanics, an inflection point is defined as a point where the curve of a physical quantity…

Q: Please turn this into 3d drawing, measurements are not important.

A: According to the question We need to find 3-D model of the drawing

Layout

The layout is a way of organizing the elements, products, and raw materials in a design. The layout is the representation of information in a structural, logical, descriptive, coherent form.The layout is a mapping of various equipment arrangements, workstations, machinery, plants, and more. It secures the continuous movement of a product quantity along with the quality.