2.5 WW 1.512 ли I 15V 812 212 MM + V₁ - 412 212 11 M P= ? 0.512 1.512 M Find I, Vi and Power Pabsorbed by the 412 Resistor

Q: Thanks for your helping

A: It is our pleasure that you get what you were looking for.

Q: The process of transferring a mobile station from one base station to another is a. MSC b. Roamer c.…

A: What is the process of transferring a mobile station form one base to another

Q: How to determine where stem locations

A: Given: To find:

Q: The process of transferring a mobile station from one base station to another is

A: The process of transferring a mobile station from one base station to another base station is a very…

Q: explain insulation coordination and write method of insulation coordination

A: We have to explain insulation coordination and write method of insulation coordination.

Q: Can I use the 66-block in telephone wire distribution to its outlets? How is it distributed?

A: According to the question, we need to explain the 66-block in telephone wire distribution.

Q: Question 10 What is the stability condition of the given system? A) Stable B) Unstable Marginally…

A:

Q: Grateful help with Part B please.  Thanks

A: Characteristic impedance is a property of the material that determines whether or not it can…

Q: make a detailed report on the type of sensors use in measuring air quality INSIDE A ROOM

A: Type of sensors use in measuring air quality INSIDE A ROOM: IAQ sensor called Indoor Air Quality…

Q: Given a single-family residence with a general lighting load of 33,500 VA. What is the demand…

A: NEC (National Electricity Code ) has defined demand factors for different types of load

Q: please could give a simplified drawn schematic/diagram to show a how  microcontroller is connected…

A: The above question is based on the interfacing of a microcontroller to a relay circuit.

Q: Grateful a little help with this homework thanks.

A:

Q: I dont get it. howcan I make sure its in low condition?

A: You have asked that how to make sure it is in low condition.

Q: Find % Regulation for the given readings VR(Line to Line ) = 394 Volts, Vs(Line to Line ) = 458 %3D…

A:

Q: A high voltage transmission line transmitting 10 MW of power operates at a voltage of 105 KV…

A:

Q: What is HT supply?

A: What is HT supply?

Q: ity or enery that are used by

A: The power system consists of electric generation, distribution and customer satisfaction. In a…

Q: Find the value of unknown. 5:100 —___:10

A: The solution is given below

Q: Number 23 please.

A:

Q: Q4: Write the following compound words in the correct form as (one word, two words, or hyphenated):…

A: AirportFossil fuelCheck-in

Q: Give the other names of depletion region? (At least Two)

A: At the junction of p-type semiconductor and n-type semiconductor, in which there  is neither an…

Q: Given a single-family residence with a general lighting load of 33,500 VA. What is the demand…

A: NEC (National Electricity Code ) has defined demand factors for different types of load

Q: List and explain types of Fire Extinguishers. What's the difference between Mechanical safety vs.…

A: Both more formal visual inspections and routine, informal "before use" visual checks enhance safety.…

Q: 5 - What should be done first when a person being electric shocked seen? A) Cut off the electricity…

A: If we seen person being electric shocked then we need to do take some necessary action

Q: The female terminals are typically located in which connector half? O Clip O Cap O Receptacle O Plug

A: Plug used to connect with the socket. The female connector is generally a receptacle that receives…

Q: L{7te¬5t cosh(3t) + +sin(Võt) – rº + e%}

A:

Q: Explain the safest one to use in an aircraft GPS OR DGPS

A: Given: GPS or DGPS

Q: P-channel MOSFET is basically a following device. a. voltage operated O b. low-frequency operated O…

A: MOSFET is controlled by the application of GATE pulse .  GATE pulse controls the conduction state of…

Q: HERE IS IT

A: Physical address can be expressed by the following formula:Physical Address = (Segment Address) x 10…

Q: where is the value of 10/sqrt(2) coming from?

A:

Q: It is not possible to locate electrical equipment in less-hazardous areas, or in nonhazardous…

A: Hazardous sites are defined in electrical and safety engineering as places where there is a risk of…

Q: Write information and introduction about UPS

A: An uninterruptible power supply(UPS) is an electrical device which provides emergency power to the…

Q: Consider a group of students that are sifting through a crate with broken or malfunctioning cables,…

A: Cable faults can be found by looking for Ethernet symbol errors on switch and router interfaces.…

Q: Discuss the difference between the off-line and online UPS

A:

Q: Look at the photo and answer the questions

A:

Q: With the help of schematics, briefly describe, how a telephone set works.

A:

Q: Discuss as to how you would connect your landline and mobile to the local telephone exchange using…

A: Mobile Telephone Switching Office(MTSO) An operations center that connects the landline PSTN system…

Q: Choose one appliance/electronic device that needs application before it can be used and explain why

A:

Q: Can you please further explain this section.

A:

Q: Hi for case 3 is explain on which question ? either (a) positive or negative or for question (b) pls…

A:

Q: Still confused about how you calculated the current. Could you please elaborate a little? thank you

A: