2.43 and 2.44 Two cables are tied together at C and are loaded as shown. Determine the tension (a) in cable AC, (b) in cable BC. 400 mm, -1100 mm- 3 m 960 mm 660 N 1.4 m B. 1600 kg 2.25 m Fig. P2.43 Fig. P2.44

Q: A uniform block of steel (SG 5 7.85) will "float" at mercury-water interface as in the figure below.…

A: Given, SGB = 7.85 SGm = 13.56 SGw = 1

Q: 6.21. The owner of the dump in Problem 6.20 suggests things would be much better if a 20-m stack…

A: Given DataFrom above question we had getemission without stack=284μg/m3QNOx=3g/sH=20m

Q: If an object is moved a distance D in the direction of an applied constant force F, then the work W…

A:

Q: 1. A measure of the sample's resistance against hydrostatic compression is 2. Biot hypothesized that…

A: Given Statement To find Appropriate phrase

Q: Problem #1. The 60-mm diameter shaft is subjected to torques as shown. If the applied allowable…

A:

Q: Problem 5. A thin oil film (u= 0.80 N - 8/m2.p=865 kg/m') of height h = 5.0 mm is squeezed between…

A: Given, Fluid Viscosity μ=0.8 Ns/m2 Density ρ = 865 kg/m2 Height h = 5 X 10-3 m Velocity of bottom…

Q: 1. Determine the moment of force F about point 0, about point A and about line OB

A:

Q: A rigid container holding superheated vapor at 4.0 MPa and 700°C is allowed to cooled naturally…

A: GivenP1=4MPaT1=700oCT2=180oC

Q: 1. Two blocks, of masses M = 2.3 kg and 2M are connected to a spring of spring constant k = 180 N/m…

A:

Q: An isentropic air compressor takes 150 m/min of air in at 10°C and 100kPa and compresses it to 1000…

A: Given: Flow rate (Q)=150m3/min Inlet temperature T1=10°C or 10+273=283K Inlet pressure P1=100kPa…

Q: 4-1 A steam cycle power system operates on an ideal Rankine cycle with two open feedwater heaters.…

A: Given data, Pressure and temperature of steam at state 7, P7 = 20 MPa and T7 = 480 °C Mass flow rate…

Q: QUESTION 2: A particle is rotating in a circular orbit with radius r=5(A+5)m. The displace- ment…

A:

Q: 11. A diatomic gas (y 1'4) does 200 J of work when it is expanded isobarically. Find the heat given…

A: Data given -  Diatomic gas Y = 1.4  W = 200 J  Isobarically

Q: (4.6) Figure 4.10 is a plot of (E) as a function of Be. Sketch (E) as a function of temperature T…

A:

Q: 3. In the figure below two equal forces are applied to the tap wrench a distance d from the center…

A:

Q: Figure Q4 shows a rod of negligible mass whose ends has to particles A and B which slides along the…

A: Therefore the position of center of mass will be at distance of “3L/4” from the end “A” and at…

Q: slope and deflection at end A.

A: for solution refer below images.

Q: The pictured system below consisting of the masses m, and m2, the massless cable and the massless…

A:

Q: Mark Billiards. Consider two #identical billiard balls (I = mR²) with mass 0.160 [kg] and radius…

A:

Q: External Force Damper Damper mass mass Smooth Surface No Friction Spring Spring sider the above…

A:

Q: Use the law of sines and the law of cosines, in conjunction with sketches of the force polygons, to…

A: The given forces are given below - F1=300 lbF2=200 lbF3=500 lb The component of the forces in the…

Q: 1. (a) If the displacement field is given by u kxy, u, = kxy, u, 2K(x + у)z where k is a constant…

A: u= ux= kxy v= uy= kxy w= uz= 2k(x+y)z Normal stress along X axis and X direction= εxx= du/dx= ky…

Q: 2. The strings AB and AC connect the 200 g ball to the vertical shaft, as shown in Fig. 2. The shaft…

A:

Q: The rectangular components of a small strain at a point is given by the following matrix. Determine…

A: Write the strain matrix. ε=εxxεxyεxzεyxεyyεyzεzxεzyεzz

Q: If an object is moved a distance D in the direction of an applied constant force F, then the work W…

A:

Q: Practice Problem 2.4.13: Calculate the moment of the force P about the axis AD using: 6 ft (a) point…

A: Given, P=240 lb The required coordinates x,y,z are, C(3 ft, 6 ft, 7 ft)E(0 ft, 8 ft, 0 ft)A(3 ft, 0…

Q: The steel framework is used to support the reinforced stone concrete slab that is used for an…

A: To Find : The load that act along members BE and FED. Given : The thickness of slab is t=200mm. The…

Q: 5275 is a commonly used grade of steel For this grade, the ultimate tensile strength fy=? Select…

A: Answer For First:- According to standard for mild steel code S275 Composition: Carbon 0.25%…

Q: How much time is required to inject a sample equal to 2.0% of the length of a 60 cm capillary if the…

A: Given that" Pressure difference. ∆P=  2×104 Pa,Viscosity, μ=0.0010 kg/m·sDiameter of the tube,…

Q: A dam on a river is built so that the wall facing the water is shaped like the region above the…

A: Given:The density of water is .The equation of curve is .The equation of line is .The water level is…

Q: Earth is rotating about the Sun in our solar system. The distance between the Earth and Sun is 1.5 x…

A: Given dataDistance between the earth and sun ds = 1.5×1011mMass of the asteroid ma = 8.9×1015kgSpeed…

Q: The rules of plane and descriptive geometry allow us to accurately project the true size and shape,…

A: Descriptive geometry allows the representation of 3D objects in 2D by using a specific set of…

Q: A piston-cylinder assembly contains 0.3 lb of propane. The propane expands from an initial state…

A:

Q: For the composite area shown below, determine the moment of inertia about the horizontal centroidal…

A: Data given- I section  Base = 180 mm  Height = 160 mm

Q: 2. Choose the correct two answers. The following properties completely fix the state of a substance.…

A: (2) A. for a saturated vapour or liquid only one property is sufficient to fix the state. B. Two…

Q: 0.4 m 0.6 m 08 m 0.6 m PROBLEMS 3.46 through 3.49* A body is suspended as shown. Write the…

A: