Advance power electronics 2.4 The measured values of a diode at a temperature of 25°C areVp =1.0V at Ip = 50 A= 1.5 V at Ip= 600 ADetermine (a) the emission coefficient n, and (b) the leakage current I,.

In this question, A diode at temperature 25°C Diode Current is given with different different…

Answered: 2.4 The measured values of a diode at a…

2.4 The measured values of a diode at a temperature of 25°C are Vp = 1.0Vat Ip 1.5 V at Ip 50 A = 600 A Determine (a) the emission coefficient n, and (b) the leakage current I,.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Related questions

Q: The input to a full-wave rectifier is 10 V AC (RMS). The load resistor is 10 ohms and rectifier…

A: Given, AC input voltage, VRMS=10 V load resistor, RL=10 Ω Power losses in rectifier, PL=2 W

Q: In a half wave controller rectifier with R load and firing angle is Tt, the average output voltage…

Q: What effect does the switching frequency have on the power loss due to the collector current during…

A: Switching means when device turns from blocking state to conduction state, and switching causes…

Q: For uncontrolled half wave rectifier, R=80ohm, L=0.15H, f=50Hz and Vm=311V. Calculate the average…

A: I_avg = Vm/(πRsqrt(1+(2πf*L)^2)) where Vm is the maximum voltage of the AC supply, R is the load…

Q: In an analog VOM, which scale calibration is not evenly divided into equal parts? A. AC ampere B. AC…

A: In an analog VOM, which scale calibration is not evenly divided into equal parts? A. AC ampere B. AC…

Q: We prefer digital systems over analogue systems for a variety of reasons

A: We prefer digital system over analog system because of few reasons.

Q: For the half-wave rectifier given in the figure below, find the average values of the output voltage…

A: It is given that : It is Half-Wave Rectifier. Vmax = 169.71 V F=50 Hz. R=1 kΩ

Q: If the time period of output voltage of a 1-o bridge rectifier is 25/3 ms, then the supply frequency…

A: Given: Time period of output voltage waveform, T'=253 ms

Question

Advance power electronics

2.4 The measured values of a diode at a temperature of 25°C are
Vp =
1.0V at Ip = 50 A
= 1.5 V at Ip
= 600 A
Determine (a) the emission coefficient n, and (b) the leakage current I,.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Subject : Electronics Engineering
Sketch the transfer characteristic vo versus vi for the limiter circuit shown below. All diodes begin conducting at a forward voltage drop of 0.5V and have of 0.7V when fully conducting at 1mA.
4. Plot the diode reverse characteristic, and estimate an approximate value for the reverse saturation current IS. From the results obtained in this experiment, compute the maximum power dissipated in the diode.
Consider the given choices
• A Si diode at a temperature of 25°C has VD = 0.7V at Is = 10nA. The temperature is raised to 125°C. 1. Calculate ID at 25°C. 2. What is effect of rise in temperature on VD & IS 3. Calculate ID at 125°C.
A silicon diode has a reverse saturation current of 50nA at room temperature (25degrees centigrade). If the operating temperature is raised by 50-degrees centigrade, what is now the reverse saturation current?
Consider a silicon pn junction diode at T 300K. The reverse saturation current is Is = 10-14 A and the ideality factor n = 1. Determine the diode current for a diode voltage of VD = 0.573 V and use that to determine the DC and AC resistance of the diode. RDC = 14.13 k rac = 639 Q RDC = 234 Q2 = rac=8Q RDC = 7.00 KQ rac = 307 Q RDC = 1.43 kQ rac = 58 Q
For a Silicon diode, the forward current is 109 times the reverse saturation current Is. What will be the value of the forward diode voltage? Assume eta to be 1.
The current measured in the circuit formed by using the ideal diode model is. Please choose one: a. 1.2 mA b. 0.87 mA C. 0.73 mA D. 0.80 mA 13:19 30.04.2021
A silicon diode is in connected to a DC voltage source with Forward biased, the net currentflowing through the diode is (25mA) where the applied voltage across the terminals of thediode is (820mV). Determine diode temperature, if Is "dark saturation current", the diodeleakage current density in the absence of light is 3.4 × 10−10 A
Determine the diode current (in Ampere) at 70°C for a silicon diode with reverse saturation current 70 nanoAmpere and an applied forward bias of 0.8 volts. The constant k value is: The Temperature (in Kelvin) is: The Diode current (in Ampere) is:
What will be the value of the reverse saturation current for a Si diode operating in forward bias mode. The following information is given: Diode current 3 A Voltage across diode 0.25 V. Temperature is 300 K.