2.4 m P = ? SG = 1.6 3 m Air D = 30 cm 60° 1 m Water

Q: Find the total pressure on a circular plate of diameter 1.5 m which is placed vertically in water in…

A: Given:Diameter of plate=1.5 md=1.5 mDistance between centre of plate and free water surface=3 mh¯=3…

Q: Determine pressure at depth of 12.33 m from free surface of water

A: Given data,  h= 12.33 m  Need to find pressure at depth of water

Q: 1.20 m wide is mounted on the vertical wall of an open rectangular tank filled with oil. The top of…

A:

Q: Ql: In Figure below find the resultant pressure force and the depth of the centre of pressure on the…

A: Dgate=4ft and dhole=.9ft since1 ft=.3048 mso Dgate=4×.3048=1.2192 m and dhole=.9×.3048=.2743 ms=.8…

Q: 3. The given triangular AB gate is hinged at A. Determine the weight of the gate that is required to…

A:

Q: What is the hydrostatic force (kN) that acts on the Gate A-B? Given that the specific gravity of…

A: Total Hydrostatic force on a flat surface in any orientation is given by :- 》》 F = ρgx¯ A Where;  ρ…

Q: Now (refer to the image) there are two identical containers as in the previous question, which are…

A: It is asked to find the pressure points 1 and 2

Q: 3 Calculate the volume if it is v1=1.5 L, P1= 100 Kpa , p2= 50 kpa.

A: Given volume at 1 = 1.5L Pressure at 1 = 100kpa Pressure at 2 = 50kpa  Volume at 2 = x L (say)

Q: A tank partially filled with water and pressurized to 6.8 psig has a circular gate in the side, 0.6…

A:

Q: The pressure at a point in the seawater is 68kpa, determine the pressure in kpa 26.87 meters below…

A:

Q: If the sloping wall is 4 m wide. Calculate the location and magnitude of the force due to the oil…

A: To find: Resultant force due to oil pressure, FR = ? The location of the above resultant force = ?

Q: (b) A cone is placed in a water tank as shown in Figure 3 (b). If the mass of the cone is 1.1 kg,…

A:

Q: PROBLEM 9: A container, in the form of an inverted pyramid with square base on the top 600 mm on a…

A:

Q: Complete 2-38 (just use Problem 2-37 for reference) 2-32 The inverted U-tube manometer is used to…

A: The densities of the respective fluids are,

Q: The gate shown is hinged at (0) contains water on one side and oil on the other. What force (F) is…

A: The expression for the area of the gate on the water side can be written as, A1=0.7 m2.8 m=1.96 m2…

Q: There are two sealed tank linked by a U-tube. If the pressure in the left and right tank are P1 and…

A: Given the pressure in the left and right tank are P1 and P2 respectively,the fluid in the U-tube has…

Q: A storage tank for concentrated nitric acid will be constructed from aluminum to resist corrosion.…

A: d = 6m H = 17 m hL = 16 m σ = 90 N/mm²     considerations : from the standard values, the density…

Q: Tank with water at 1 m depth and oil on top with 0.3 depth (S.G = 0.8) calculate the absolute…

A:

Q: Calculate the pressure at the bottom of the spherical tank, 3.6 m in diameter, filled with peanut…

A: Write the given data: d=h=3.6 mS=0.92Po=82 kPa

Q: Figure Q2 shows two tanks which contain the solvent used for plastic manufacturing. Tank A contains…

A:

Q: Find the capillary raise of the water in the tube of diameter 2mm, which is immersed vertically in…

A:

Q: ?What is the total force lifting the tank

A:

Q: A U-tube manometer contains a liquid having a 3 density of 800 kg/m. When the manometer is connected…

A: The absolute pressure of the gas is 1.023544 bar.

Q: 3. Calculate the volume if it is v1=1.5 L, P1= 100 Kpa , p2= 50 kpa

A: Given data: V1 =1.5L P1=100 kPa P2=50 kPa Need to determine the volume at state 2.

Q: What are the pressures at the A(conjunction of water and oil), B (middle of water), C (bottom of the…

A:

Q: The system consists of a pipe with a diameter of 0.05m and a length of 4 m, and a hemisphere (radius…

A:

Q: Consider a differential manometer whose ends are connected to two different pipes A and B and…

A:

Q: 1.5 must be used. Pulley diameters are 9.75in, and tum 1750rpm. Compute fc e following: Design Power…

A:

Q: The maximum safe compressive stress in a hardened steel punch is limited to 1 GPa and the punch is…

A:

Q: cubical tank of 2 m side contains oil of relative density 0.8 to t depth of 0.6 m and sea water of…

A: The side of cubical tank is The relative density of oil is .The height of oil is .The relative…

Q: 8. The lower half of a 10-m-high cylindrical container is filled with water (p= 1000 kg/m²) and the…

A: Given: Height of the cylinder→h=10 m Density of water→ρ=1000 Kg/m3 Specific gravity of the…

Q: ersed rectangular plate as shown in the figure. Free water surface Im b-3 m

A: Solution is attached below:

Q: this solution doesnt give the final answer of finding the pressure at point A

A: From follow up to an existing solution of a question, we have following information. Total bend loss…

Q: How does the depth of the center of pressure and the depth of immersion related?

A:

Q: If the wall in following figure is 4 m long, calculate the total force on the wall due to the oil…

A:

Q: 2. A vertical rectangular gate 1.75 m wide and 2.75 m high is submerged in water with the top edge…

A: Given data  Width of gate = 1.75m Height of gate = 2.75m Find the total pressure and location from…

Q: Problem 1: The figure below shows a vacuum tank with a flat circular observation window in one end.…

A: