2.16. The stress at a point is defined by the components Oxx = MPa, Ozz = 70 MPa, Ory = -80 MPa, ơyz = Ozx =0 MPa, so that o2z is a princi- pal stress. Find the other two principal stresses and sketch the three Mohr's circles. Hence determine the magnitude of the maximum shear stress. 120 MPa, ơyy =300

2.16. The stress at a point is defined by the components Oxx = MPa, Ozz = 70 MPa, Ory = -80 MPa, ơyz = Ozx =0 MPa, so that o2z is a princi- pal stress. Find the other two principal stresses and sketch the three Mohr's circles. Hence determine the magnitude of the maximum shear stress. 120 MPa, ơyy =300

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the plane stress sigma x = -8MPa, sigma y = 7MPa, tow xy= 6MPa cw, draw a Mohr’s circle diagram properly labeled, find the principal normal and shear stresses, and determine the angle from the axis to . Draw stress elements
Suppose that σ = 330 psi and Try = 150 psi in (Figure 1). Figure Part D Specify the orientation of the principal stress. Take the positive direction of rotation counterclockwise. Express your answer in degrees to three significant figures. Op₁= Part E OF 0₂ = ΑΣΦΙΚΗ vec Specify the orientation of the maximum in-plane shear stress. Take the positive direction of rotation counterclockwise. Express your answer in degrees to three significant figures. 0/ —| ΑΣΦ 11 | vec ? ? o
For the stress state: Oz = 30 ksi, oy = 40 ksi, Try = -10 ksi a. Find the principal stresses and draw the stress element in the principal orientation. b. Find the maximum in plane shear stress and draw the stress element in the maximum in plane shear orientation.
4-6 if possible
From the stress states given, draw the 3D Mohr's circle (lable the principle normal stresses, maximum and absolute shear stresses), and sketch the principle and shear planes. σxx = 70 ksi, σzz = -50 ksi, ?xy = 50 ksi (counterclockwise)
Draw the Mohr’s circles. Fill in the blanks. Stresses are in ksf.
For the shaft shown below, determine the normal and shear stresses acting on the element located at point A, including stress concentrations. Then draw the stress element at A with the applied stresses and determine the three principal stress (0₁, 2 and, σ3) using Mohr's circle. r = 0.0042 m, d = 0.03 m, D = 0.033 m, T = 250 Nm P = 1500 N, M = 300 Nm, A M M DEHRƏC T d T P P r
Determine the state of stress at point q. The pipe has an inner diameter of D₁ = 1.0 in and an outer diameter of = 1.8 in. Use the exact expression for Q, if needed. Label the reultant forces on the cross section below. Report your answer (3x3 matrix) in psi to one decimal place. Do 4 in. Y 4 in. 150 lb 6 in. 50 lb 10 in. 200 lb 150 lb X N Y
Problem 3. Strains are measured on the surface of a structural component as &A = = 1200 x 10-6. EB = 500 x 10-6, &c = 300 × 10-6. E = 200 GPa and v = 0.3. b) a) Find the principal stresses and show these on a sketch of a properly oriented element. Use Mohr's Circle to find the stresses at 0 = 30° counterclockwise from the x axis and show these on a sketch of a properly oriented element. y 60° C B A X
4. The general stress element is loaded such that ơx = 30 MPa, oy = -20 MPa, Txy = 5 MPa. Using Mohr's circle, find out the maximum normal stress and shear stress acting on this element. 5. The general stress element is loaded such that ơ, = 50 MPa. Using Mohr's circle, find out the maximum normal stress and shear stress acting on this element. (Simple tension)
2.7. The principal stresses at a given point are ơj =10 MPa, ơ2=-100 MPa. Sketch Mohr's circle for this state of stress and determine the normal stress on a plane in- clined at an angle 0 to the principal plane 1. Hence find the range of values of 0 for which the normal stress is tensile.