QUESTION 022.1A pipeline connects two reservoirs such that the total head between them, whenwater is being pumped from one to the other can be expressed as H= 25 + (77,46Q)²where H is the total head (m) and Q is the discharge in m³/sec. The characteristiccurve of the particular pump that can be used, is tabulated as follows:Head (m)756555453325Discharge (m³/sec)0,020,030,040,050,0550.70087030(%) LIEvaluate graphically the discharge, head and efficiency if:is used2.1.1 One pump2.1.2 Two pumps are used in series.2.1.3 Two pumps are used in parallel.

a) When one pump is used From curve, H=25+(77.46Q)2 Q (m3 /s) Head, H(m) η(%) H(m) System curve…

Answered: 2.1.1 One pump is 2.1.2 Two pumps are…

Engineering

Civil Engineering

2.1.1 One pump is 2.1.2 Two pumps are used in series. 2.1.3 Two pumps are used in parallel.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem 7: The two pumps in problem 6 are now arranged in parallel. The static head is 40 ft. The…

A: Given that the two pumps are connected in parallel. The static head is 40ft. Hs = 40ft Diameter, D =…

Q: A certain part of cast iron piping of a water distribution involves a parallel section as shown in…

Q: Ex. Drive the Bernoulli eg. For the fig. show the discharge flow 0.5m3/sec and find h density of…

A: Given data - pw = 1000 kg/m3 phg= 13600 kg/m3 Q = 0.5 m3/s Find out - Value of h ?

Q: A single pipe of length 1500mand diameter 60 cm connects two reservoirs having a difference of 20 m…

Q: I A pump impeller is 37.5 cm in diama and discharges water with velocity components of 2 m/s and 12…

Q: a sump to an overhead reservoir. The static lift is 40 m out of which 3 m is the suction lift. The…

Q: 2 and 3 from three reservoirs A,B and C, respectively, meet at a junction whose elvation is 366 m.…

A: Given:- elevation=366m Water levels at reservoir A and B are elevations =825 m and 716 m pipe 1:-…

Q: A A 2 B 1 The three-reservoir system is shown below: C The elevation of Reservoir at A is 140m and…

A: Given data in question Diameter Discharge from pipe 1 Friction constant Length of pipes Heights…

Q: Which of the following is a valid potential function for incompressible flow? (Assume A is numerical…

Q: Two reservoirs 1500 m apart have a water surface elevation difference of 18 m. A cast iron pipe with…

Q: Two reservoirs are connected by two pipes P and Q. The pipes have the same diameter and length and…

A: Given data: Two reservoirs are connected in parallel by two pipes P and Q. Friction factor of P is 9…

Q: Determine the elevation of the free surface in Tank B if the total discharge into Tank B is 5.00…

A: ###Determination of Elevation of Tank B###

Q: Calculate the pump capacity

A: Given, Pipe length (L) = 73 m Pump efficiency = 75% D1 = 2 in or 0.05 m D2 = 1.5 in or 0.0375 m

Q: The 150-mm pipeline shown below conducts water from the reservoir and discharges at a lower…

A: The diameter of the pipeline = 150 mm The diameter of the discharge = 50 mm The elevation of the…

Q: Problem-4, A pipe of 0.7 m diameter has a length of 6 km and connects two reservoirs A and B. The…

A: Given- Diameter d=0.7 m, Length L= 6 km, The water level in reservoir A is at an elevation 30 m…

Q: 5. It is desired to deliver 5 gpm at a head of 640 m in a single stage pump having specific speed…

Q: 6. A water is supplied through the pipe network system as shown below. The reservoir water level…

Q: Operating point of a pump is obtained through the intersections between the system curve line with…

A: Given, Reservoir system connected by pipe

Q: water pump at elevation 46 m. is used to bring up 250 gpm of water from a river (elev. 45 m.) to…

A: Discharge is 250 gpm Elevation of reservoir is 100 m

Q: A 13-cm diameter pipe of length 100 m with z = 60 m and f = 0.02. What is the flow rate? D=13cm,…

Q: El. 200 mA A Res. H-W Pipe B Pipe E pipec → Negleet minor losses → Pipes B, C, and E are all have: L…

A: Vc = 5m/s

Q: The system shown below consists of 1000 m long and 50 mm diameter cast iron pipes. With a volume…

A: The given figure is shown below:

Q: The specific energy, E, is defined as the total energy head with respect to the channel or pipe…

A: Given data : Flow rate (Q)=1 m3/sWidth (w)=5 mDepth (d)=20 cm

Q: Târee reservoirs A, B, and C are connected respectively with pipes 1, 2, and 3 joining at a common…

A: Given : Elevation of reservoir A = 80 m Elevation of reservoir B = 70 m Elevation of reservoir C =…

Q: servoirs A, B and C, respectively, and meet at junction D. The elevation of A is 300 m while that of…

A: Given Discharge through pipe 2 = 560 l/s

Q: A pump draws water from an open reservoir, with a static suction head of 26.24 feet, and lifts it to…

A: Given: Static Suction head H1= 26.24 feet= 8mStatic discharge head H2 =25 mDiameter of suction pipe…

Q: A centrifugal pump discharging 900 gpm and operates at 1800 rpm against a head of 120 feet has a…

Q: A pipeline is being designed to pump 0.5 m3 /s of water at 25°C through a concrete pipe. The…

Q: A wastewater pump is discharging at a rate of 0.5 m3/s. It has a discharge nozzle diameter of 350 mm…

A: According to given data A wastewater pump is discharging at a rate of 0.5 m3/s.It has a discharge…

Q: 1. Four reservoirs are connected as shown below. Minor losses can be ignored. Determine the flow…

A: Four reservoirs are connected as shown in the figure.Coefficient of friction, f = 0.02Pipes Length…

Q: 12. For the Dam shown in the figure a) Draw the flow net in the soil under the dam b) Calculate q…

A: Note :- nothing said about how many flow lines and equipotential lines to be drawn so taking it as…

Q: The three-reservoir system is shown below: A A 2 1 3 C The elevation of Reservoir at A is 140m and…

Q: 1.78 67 2.67 ies in a system having a static l inor loss coefficient of 20. Dete

A: two siphons are in seriestotal head H =80 ft length L=1200 ftdiameter =6 inches =612 ft' =0.5 ft f…

Q: Problem 3 A reservoir with water is pressurized as shown. The pipe diameter is 1 in. The head loss…

A: Detailed solution is given below, still if you have any query please feel free to contact me.Thanks…

Q: he water system consists of a reservoir with a the pipe entrance is sharp-edged pipe entrance, a…

A: A turbine is normally a machine that works under the action of a fluid surface with a circular set…

Q: The table below gives the pump curve data for a pump operating at 1000 rpm and has 3-in. impeller.…

A: Given Data: Speed of Pump 1 is N1=750 rpm. Speed of Pump 2 is N2=500 rpm. Speed of Pump 3 is N3=600…

Q: Two reservoirs are connected by two pipes P and Q. The pipes have the same diameter and length and…

Q: Water is pumped from reservoir A at elevation 250 m. The pump is close to reservoir A and is at the…

Q: What is the required pump power (Pa) for the system below?

Q: For the branching pipe system shown, determine the flow in each branch. The fluid in each reservoir…

A: Given:For branch-A:L1=5000 mD1=1.5 mz1=135 mFor branch-B:L2=800 mD2=50 cm=0.5 mz2=120 mFor…

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water is to be moved from one large reservoir to another at a higher elevation as indicated in figure shown The loss of available energy associated with 2.5 ft^3/s being pumped from sections 1 to 2 is 120 times of the velocity head. Determine the amount of shaft power required. Section (2) Bn inside diarmeter pipe 3D I 500 Section (1) Pump Select the correct response 1.14 hp 1.28 hp 1.07 hp 1.56 hp
Upper reservoir elevation = 100m Lower reservoir elevation = 50m %3D The penstock pipe in between the two reservoir has a length of 180 meters, friction factor f = 0.02, pipe diameter of 400mm, with flow rate of 900 L/s. %3D Determine the head in meters that the turbine can extract.
Problem 5 Consider a three-reservoir problem with the following characteristics. L₁ = 95 m L₂ = 125 m L3 = 180 m Z₁ = 25 m Z₂ = 115 m z3 = 85 m (a) All three pipes are constructed of 28 cm, unfinished concrete (e = 1 mm). If water at 20 ºC flows through the pipes, compute the steady flow rate in each pipe (magnitude and direction). (b) Reduce the diameter of all the pipe to 15 cm, unfinished concrete (€ = 1 mm) and show that the flow rates distribute in nearly the same manner but are about 5.2 times lower. Explain why.
Q2/B /Water is transported from a reservoir at higher elevation to another reservoir through a series of three pipes. The first pipe of 0.4 m diameter is 500 m long, the second pipe 600 m long, size 0.3 m, and the last pipe is 500 m long of diameter 0.2 m. If the elevation difference between two reservoirs is 30 m, calculate flow in the pipes. (S)
Solve please
find the discharges in each of the pipes for the following pipe network configuration Given data L = 200 m D = 4cm f = 0.05 15 cumec A E B D с 15 cumec
NEED COMPLETE SOLUTION. NEED ASAP. Thnak you
Assume that the width of the tank is equal to 1 m. Find force F1 and F2.
Consider the figure below. The pump supplies water from reservoir A to reservoir B through the 500mm o pipe, 600m long. Using f = 0.02 and the hydraulic grade line shown, determine the following: a) power supplied by the pump, b) power loss by the turbine, and elevation maintained by reservoir B. El. 200 hfj El. 190 НЕ El. 180 hf, B El.100 A P TURBINE PUMP ANSWER: a. Power = 1557.828 kW, b. Power = 155.7828 kW c. Elevation of B = 170 m %3D
Two sharp-ended pipes of diameter d₁ = 50 mm, and d₂ = 100 mm, each of length 100 m, are connected in parallel between two reservoirs which have a difference of level h= 10 m, as shown in figure below. If the friction coefficient, f= 0.032 for each pipe, calculate: a. the rate of flow for each pipe, b. the diameter d of a single pipe 100 m long which would give the same flow if it was substituted for the original two pipes, (Notes: Use Darcy Weisbach's equation, h,= (flv²)/(2dg) Pipe 2- Pipe 1 h = 10 m 110
Answer Question 6: the marked choice is the correct answer.
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m^3/s is to occur in the cast iron pipe. Use f= 0.0021 for all pipes. Include minor losses. (DO NOT ROUND OFF)