2.

Q: How can you use 2 to 1 Mux to construct 16 to 1 Mux.

A: 16 to 1 MUX using 2 to 1 MUX:

Q: QUESTION 7 For the voltage-divider configuration find a) IB b) IC C) VB d) VE e) VCE VBC 20 V 40 k2…

A: In the BJT circuit,  Find the all current and voltage.  DC gain = 100  We are solving this problem…

Q: A Moving to another question will save this response. Question 4 For decimal numbers the base is…

A: Decimal number - It can be defined as a number whose whole number part and fractional part is…

Q: Q2-A For the following circuit, determine the expression of the output x without simplification.…

A: Give that: The circuit is

Q: Referring to Figure 1 below, answer the 2 15 1 05 0 05 -15 10 questions below. 2 15 1 05 0 15 10 12…

A:

Q: What can you determine about the circuit being tested based on what is displayed on the DMM?

A: Circuit shows three lamps, dome lamp, Lamp A and Lamp B are  connected in parallel and supplied…

Q: The table shows the set of five measurements recorded in a laboratory. The precision of 4th…

A:

Q: Question#3 Draw the characteristic table and the state diagram for the shown circuit Y1 Y2 CLK Z1 J…

A: The given circuit diagram is:

Q: It's hard to read，  I need handwrite solution

A: Given: To find: For all circuits, i) Transfer function, ii) Magnitude response, iii) Phase…

Q: How to calculator the resistanc

A: If you know the total current and the voltage across the whole circuit, you can find the total…

Q: X-When several persons are electrocuted, the first to expire is the one nearest the source. Y- A…

A: X- when several persons are electrocuted the first to expire is the one nearest the source.  Y- a…

Q: How can this be represented on Tinkercad?

A: The given circuit isWe need to represent the above circuit on Tinkercard.

Q: Q#3: Consider the system described by: x(k + 1) = [, 7}x(k) + [««) y(k) = [-3 1]x(k) a) Find the…

A: The given system is described by: xk+1=1-107xk+01ukyk=-31xk Here, A=1-107B=01C=-31 To find: (a) The…

Q: t1/2 = (Rln2)C, how do I find the time constant if the resistor value is unkown?

A:

Q: This part which is also known as the dial or infinity knob allows you to adjust the pointer to the…

A: Adjustment screw is used .

Q: 5. Using nodal analysis, find V₁, V₂ and V3 GA(1 V₁ 92 M € 45 8A 322 W V2 ≤422 62 W V3 $82 9 v

A: The given problem is from nodal analysis. The detailed solution is given in the next step

Q: Find three patterns respositories for user-Interface patterns, select one patterns from each and…

A: Three patterns respositories for user-Interface patterns are, Welie pattern library Yahoo design…

Q: 12 15 16 None of the other answers are true

A:

Q: 5. Refer to Graphic E. What is the voltage across R2? 1.93 V 2.76 V 3.16 V None of the above

A:

Q: A 66 block is a punch down block which has rows of four metal pins.

A: A 66 block is a punch down block which has 50 rows of four metal pins.

Q: 7cos (300t) qik Fluf K4) a) find Do lt)

A:

Q: observe what happens when th buttons are pushed? PB1 PB2 o M2 MI # Fill in the table: LAMP PB2 off…

A: PLC refers to programmable logic Controller. It is a solid state computerized controller. PLC is a…

Q: 23. What is the waveform across D1? halfwave fullwave sinewave DC line 24. What is the waveform…

A: 23. whenever diode conducts then voltage across the diode is constant i.e, for silicon diode it is…

Q: please redesign this please. AND Gate. same switches, power supply but different layout. thank you

A: The logic circuit is given as

Q: For analog signals: They vary in a smooth way over time They give an output that varies continuously…

A: Analog signals: A signal is an electric or electromagnetic data which is transferred from one…

Q: QUESTION 6 What is this a diagram of? O NO pushbutton ONC temperature switch ONC level switch ONC…

A: Introduction: Various parts are required to configure an electrical circuit. To understand…

Q: Q3: what are the counting states for this counter? CK KO 12

A: A counter is a sequential circuit whose state represents the number of clock pulses fed to the…

Q: this version is hard to read， I need a handwrite version

A:

Q: The type of error that is associated with measurement instruments or techniques is error.

A:

Q: Please help me make these two circuits on TinkerCAD. I am having trouble understanding how to make…

A: Need to connect the given circuit in the tinkercad and then analyze the circuit with various input…

Q: Pt = Pt = P+ = Pt Pr G+ x Gr > (4nd)² 1x106 (00X100 x/0.112 1x 10-6 4X3.14 X 600² 10000 x 0.1…

A:

Q: ct Fluke T5 and DMM Questions These questions apply to the T5 and/or the Fluke DMM. You will likely…

A:

Q: Count

A: In this we have to write 0 to 25 decimal numbers to hexadecimal numbers..

Q: In the 4-variable K-map the cell with address 1100 is adjacent to the cell that has the address: O…

A:

Q: 1. Solve the tollowing unknowns. Tabulate your answer. R1 R2 Vs -ov R3

A:

Q: If the voltage on pin A3 is 0.752V, what value will analogRead(A3) return from the ADC?

A: Given, Voltage on pin A3 (V) = 0.752V We know, for ADC, Resolution bits (n)=10  The reference…

Q: Question 3 Doping is done in a semiconductor material to Increase the number of charge carriers O…

A: The given problem is from semiconductor device   The solution is given in the next step

Q: Fill in the Blank: A 66 block is a block which has 25 rows of four metal pins.

A: A 66 block is a telephone wire distribution system.

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.