2. Write the necessary commands to configure Inter VLAN communication (Router on aStick) for the following topology.Delaut Router431 10.1.1.2/24p route 0.0.0.0 0.0.0.0 10.1.1.210.1.1.1/24interface vian10oaddress 192.1e.10.1 255.255.2ssointertace vian30ip address 192.160.30.1 255.255.255.0Mutia witchoLaptop-PTLaptopoLaptop-PTLaptopo(1)PC-PTPCO(1)PC-PTPCOVLAN 10VLAN 30Laptop-PTLaptoPC-PTPOO(2)VLAN 20interface vlan20paddress 192.160.20.1 255.255.255.0

2. Write the necessary commands to configure Inter VLAN communication (Router on a Stick) for the following topology. Detauit Route 1 10.1.1.2/24 route 00000.0.0.0 10.1.1.2 10.1.1.124 face vian10 ads 192.18 10.1 255 255 255.0 intertace vian30 paddress 192.166.30.1 255.255.25s.0 Laptop-PT Laptop PC-PT POO(1) Laptopo(1) VLAN 30 VLAN 10 Laptop-PT Laptop0(2) PC-PT POO(2) MAN 20

2. Write the necessary commands to configure Inter VLAN communication (Router on a Stick) for the following topology. Detauit Route 1 10.1.1.2/24 route 00000.0.0.0 10.1.1.2 10.1.1.124 face vian10 ads 192.18 10.1 255 255 255.0 intertace vian30 paddress 192.166.30.1 255.255.25s.0 Laptop-PT Laptop PC-PT POO(1) Laptopo(1) VLAN 30 VLAN 10 Laptop-PT Laptop0(2) PC-PT POO(2) MAN 20

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

The following is a partial output from a show command on a router: Neighbor ID Pri State Dead Time Address Interface 192.168.1.1 150 FULL/DROTHER 00:00:16 192.168.1.1 FastEthernet0/o 192.168.1.2 100 FULL/DROTHER 00:00:16 192.168.1.2 FastEthernet0/0 show ip protocols O show ip ospf neighbor show ip eigrp neighbor O show ip neighbor
2. Do the following for the given network (write the commands for each of the router). 192.168.1.1/24 192.168.1.2/24 192.168.2.1/24 192.168.2.2/24. fa 0/0 Router-PT fa 0/02outer-PT se 2/0 se 2/0 Router-PT Router2 Routero Router1 Tasks 1. In router, assign IP address for interfaces. 2. Set the name for the router as given. router 0 name as UOB, router 1 as Buraimi, router 2 as Sohar Set MOTD on all routers to *****UNAUTHORIZED ACCESS IS NOT ALLOWED ***** 4. Assign the Console password of all the router to " Sunrise".
Q1: Simple, compare between each of the following? TCP and UDP protocols Network and transport layers RDT 2.1 and RDT 2.2 Pipelined protocols and Stop and wait protocols Q2. Write the definition of each TCP header filed. Q3. State and example to clarify the bad performance of RDT 3.0
1. For the given network, write the commands that are used in the host and Router for configuring the Router on a stick. 192.168.2.2/24 vlan 5 sub interface 0/1.5 for vlan 5 (p address 192.168.2.1) sub interface of1.10 for vlan 10 (p address 192.168.3.1) 192.168.1.1/24 PC-PT Ha0/5 PCO fa0/1- Ha0/1- fa0/10 2950-24 1841 Switch2 Routero PC-PT PC1 192.168.3.2/24 vlan 10
List all the static routes on each of the 4 routers required for full communication across the topology. The addresses with question marks have been relabeled. I think each router should have 3 static routes. This is using the ip route command (ip route <netid> <net mask> <next hop>)
What static routes need to be added to routers A and B for PC communication across the whole topology?
Hello, the questions are detailed in the attached picture. Thank you
We have two routers called router spade and router Hearts How it’s work?
Assuming that the OSPF priority is the default value, determine the router-id for each of the routers on network 192.168.100.0/24* R1 R2 R3 Router ID: 172.16.0.1. No Router ID No Router ID No Loopback O No Loopback 0 Loopback0: 10 10.10.1 GO/1. 192.168.100.100/24 GO/1 192 168 100 101/24 Loopback1 10 10 20 1 GO/0 172.16.10.1/24 S0/0/D: 72 100.10.1/30 GO 192 169 100.102/24 G0/0: 172 16.30.1/24 72/160.1 192.168 100/100 192.168.100.101 72.100.10.11010.10 1 10 10.20 R1