2. Water flows out of the reducing elbow at 3 ft³/s. Determine the horizontal and vertical components of force that are necessary to hold the elbow in place at A. Neglect the size and weight of the elbow and the water within it. The water is discharged to the atmosphere at B. Fy 0.40 ft. Fx 60° B 0.20 ft. pressure Flow and area

2. Water flows out of the reducing elbow at 3 ft³/s. Determine the horizontal and vertical components of force that are necessary to hold the elbow in place at A. Neglect the size and weight of the elbow and the water within it. The water is discharged to the atmosphere at B. Fy 0.40 ft. Fx 60° B 0.20 ft. pressure Flow and area

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. A square frame 3m by 3m in dimension is submerged in water vertically with its top 4m from the surface. If oil (s = 0.80) occupies the top meter. a. Determine the horizontal pressure acting on the frame. b. Determine the pressure at the top of the gate. c. Determine the pressure at the bottom of the gate. 3m oil water |--3m- s=0.80
A rectangular vertical gate that has a width of 0.6 meters, height of 2.45 meters, and it weighs 1.78kN is hinged at the bottom. On the right side of the gate the water has a height of 1.8 meters while on the left side of the gate the water has a height of 4.9 meters. However, the gate is held in place by horizontal force F applied at the top of the gate. Determine the horizontal force F and the reactions at the hinge. The weight of water is 9.81 kN/m3
3) Gate AB is 3.20 m long. Find the horizontal force H to hold the gate in equilibrium. (Width of AB is 2.0m). 60 cm Oil (8 0.80) Water 60° H
Water flows through the elbow. It exits to the atmosphere at section 2. The inlet and exit pipe diameters are D,=10 cm and D2=3 cm, respectively. At a weight flow rate of 169,9 N/s. The elevation difference between the inlet and outlet sections is 25 cm. Neglecting the weight of water and elbow, estimate the force [N] on the flange bolts at section 1. (NOTE: pwater=998 kg/m³) 25 cm 40°
The 600-Ib, 20ft-wide rectangular gate shown is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force P at its center. A. Determine the magnitude if the hydrostatic force acting on the gate using the hydrostatic panel equations. Express your answer in kips.
End of the question 10 N not the grade
Q| As shown in figure below, determine the weight of concrete cylinder, for equilibrium the gate AB. The gate AB weighs 20 kN. Pulley Cable Cable Gate wide 3m B Concrete cylinder 90° Water Sm 2.5m 30 Hinge
HELP ASAP ? THANKS
Need help. Thanks
The dimension of the display window at the Georgia aquarium is 5m x 5m. Assuming that the aquarium contains water(ywater=9810 N/m³), find: a) The maximum pressure acting on the window b) Magnitude of the resultant force on the window c) Location of the resultant force 12m Water 45 Display windo 1.
Find the resultent force f center of pressure for one Q7: side of submerged area shown in figure below. Water 1-3M 0.75 m 0.Sm hole of dia. = 0.6 m 1.5 E 1.5
Determine in psi the pressure drop between the ends of this duct.