Answered: 2. Using data sheet of 2N 3904, IC max…

2. Using data sheet of 2N 3904, IC max =200 mA, Calculate RB and RC for Transistor Circuit of maximum IC for VCC = 12V and VBB = 4 V, Show all your work R₁ VBB+ RB ww Q₁ 2N3904 Vcc

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Hi, Sketch i0 and v01 for the network below for the input shown (Both diodes are Si. VD=0.7 V) Can…

A: From the given input waveform the maximum value of the input voltage is Vimax = 20 V Vimin = -20…

Q: Solve the collector-emitter voltage (VCE) of Figure 612. VCC T8V Beta = 110 R2 3.9kQ Figure 612…

A: We need to find out collector to emitter voltage for given circuit

Q: Sketch the DC load line for the fixed bias circuit and place the Q-point on it. ( !(a VCea) : (1.24…

A: Given

Q: Assume each diode to be OFF when V₂ ≤ 0.7V and ON when VĎ >0.7V. Find iD1, İD2, İD³, and vō in each…

A: Given:a circuit,when , the diode is off. when , the diode is on. Find:iD1, iD2, iD3 and v0.

Q: An abrupt silicon pn junction at zero bias has dopant concentrations of Nd = 1 X 1017 cm 3 and N₂ =…

A: Given,

Q: Assume VBE 0.7 V and ß 50 for the transistor in the circuit shown in the figure. For VCE - 2 V, the…

A: Given- Voltages- VBE=0.7 V,β=50,VCE=2 V, To Find- The value of RB.

Q: For a silicon BJT shown in figure find Rg that establish VCE = 2 V. Assume VBE = 0.7 V +12V www R₂ B…

A: Given circuit: VCC=12 V. Collector resistance, RC=5 kΩ. Current gain, β=50. VCE=2 V.VBE=0.7 V.

Q: A fixed bias n-channel JFET with Vdd= 12V, Rd= 1.2k ohms. Idss=12mA and Vp=-4V. Determine Vs. a.0 V…

Q: +20 V Rc RE -20 V Vc An NPN transistor in active mode has the following characteristics: VBE = 0.7 V…

Q: Dreaw the output voltoge waveforem B(t) that is, how the outpat voltoge Vo changes as a fundtion of…

A: Upper Diode is become open circuit when V1 voltage and 3V voltage is applied across the diode…

Q: Draw a circuit with silicon diodes that has the transfer characteristic shown in figure (3). AVo 4.5…

Q: The graph below shows the i-v characteristic curve of a certain diode. Id 6.0 5.0 4.0 3.0- 2.0 1.0 I…

A: Given graph : Values of ID at different voltages VD

Q: For the circuit if R=10Kohm,V=5V, Vm=10V then draw the output waveform vo. Consider diode ideal

Q: b) Determine the Quiescent Point (Q point) for a silicon transistor with ẞ = 50 in the voltage…

Q: B) For the circuit shown below, what is maximum load current It that can be drawn from the Zener…

Q: 4. For the circuit shown in the figure below find the following a. Write the name of the circuit....…

A: For the given circuit find the following parameters : Name of the circuit. Find the value of IB, IC…

Q: Plot the output of the circuit shown below. The diode is made of silicon with knee voltage = 0.7 V…

A: Since you have posted the multiple questions so we are supposed to answer the 1st one.In the given…

Q: following components: DC supply, 1k resistor and a) Ideal diode b) silicon diode Vi (V) Vo (V) 10-…

Q: In the circuit, R=3k ohm , RR= 300 ohm. What is the Va voltage. After you make solution make…

A: the circuit have 4 diode, and resistance. The value of R=3k ohm , RR= 300 ohm What is the Va…

Q: The term "Bipolar" in Bipolar Junction Transistor (BJT) refers to a) Two junctions c) Two polarity…

A: BJT- (BIPOLAR JUNCTION TRANSITION) - bjt is a solid state device current to be flow two terminals…

Q: Write an expression for the output voltagein terms of the input voltage for the circuit. Diode D is…

A: Given: Th diode is connected to form the diode connected transistor. The transistor being used are…

Q: B. Determine the collector current in Q4 and reference current Ix of the circuit below. Assume…

Q: (c) Draw with complete labelling an equivalent circuit that represents the circuit in Figure A.2.…

A: We need to draw equivalent circuit for given circuit

Q: 245 kohms 275 kohms 265 kohms VBB 255 kohms yu The transistor of following figure in Si diode: The…

Q: Izl min=lmA ZDi Vzl=3.1V Iz2 min.=1.5mA The maximum power of each of the three zener diodes in the…

Q: 1.) Where does the resistor comes from in segment 1 and 2? a. Capacitor, Diode b. Diode, Diode…

A: -A filter circuit is a device that removes ac component of rectifier output but allows the dc…

Q: TM S UTM (b) SUTM (1), the output voltage, Va TM SUT (ii) the voltage drops across series…

Q: Determine the Collector Current, IC.

A: The base current can be found by applying the KVL equation to the input loop: So, the equation can…

Q: F. The main types of fielde D BJT and FET UJT and FET JEET and MOSEET

A: Since you have asked multiple question ,we will slove the first question for you .If you want any…

Q: AV,= 50 mV IzK - 10 mA Alz= 5 mA 15 mA IR Figure 5

Q: VCE at B-80 of the silicon transistor shown in the figure below is equal to 150KSL §2KZ VCE 6.58 V

A: The current through 2k ohms resistor is IC+IB. Apply KVL to the output loop.…

Q: Find the Q point value of the diode current and the voltage gain Av in the following circuit:

A: According to the question, for the circuit shown belowWe need to find Q-point value of the diode.

Q: Q1 Given circuit below. BJT is specified to have ß-100 when in active mode and |VBE 0.7V. Find…

A: The given circuit isβ=100.|VBE|=0.7 V.We need to find all the currents, node voltages and mode of…

Q: 5. A pn junction diode has a reverse bias capacitance Cj = 75 fF. Cjo = 150 fF. The reverse bias…

A: According to question:

Q: (+) 0.25 V_SIN RL -1 V_SQR 0.75

A: To solve above give problem concept required are: A diode is turn on when forward voltage is applied…

Q: What type of semiconductor device is the following current-voltage relationship most likely to…

Q: For a voltage divider JFET

A: JFET- Full form of JFET is Junction Field Effect Transistor it the simplest form of field-effect…

Q: Using complete diode model and assuming that the forwyd resistance of thediode is 152 and a…

Q: Determine the I I,V and V for the transistor circuit in Figure. B, cBE Rc 430 0 Vcc Poc =50 24 V 4.7…

A: Given,

Q: The term "Bipolar" in Bipolar Junction Transistor (BJT) refers to O Two diodes O Two polarity…

A: We need to tell about BJT

Q: What is the Q-point for a biased transistor as in Figure F with Ig = 70μA, BDC 110, Vcc = 24V, and…

Q: Collector characteristics for the Ge transistor If VEE =2 V, VCC =12V, and RC = 2k , size RE so that…

A: For a Ge transistor - VEE=2VVCC=12VRC=2kΩVCEQ=6.4 V

Q: For a diode with Vy 0.7 v , rf = 10 Q , as ID increase , then Vy O increase decrease O unchanged O…

A: Vy is built in potential which doesn't depends on applied current

Q: Assume a knee voltage of 0.7V and B-120 for all transistors. Determine the Ve. 5VDC CO 1 0M2 3002 Vc

A: Redraw the circuit diagram,

Q: 1: Prove that the dynamic resistance of diode is ra=26mv/Ip.

Question

2. Using data sheet of 2N 3904, IC max =200 mA, Calculate RB and RC for Transistor Circuit
of maximum IC for VCC = 12V and VBB = 4 V, Show all your work
VBB +
I
RB
www
R₁
ww
Q₁
2N3904
Vcc

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: What is bjt

VIEW

Step 2: Rb and Rc calculation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

9J why r so much less is the base current in a transistor than the Collecfor current?
For the following circuit: Find the current that goes through each diode. What's the value of Vo? Invert polarity of the 5V source and obtain the following: Find the current that goes through each diode. What's the value of Vo? V1 -5V H D1 1N4001 R2 >1kQ 11 D2 1N4001 R1 2kQ ww R3 1kQ Vo Use simplified model
Figure 1 shows a voltage-divider biased transistor circuit. If βDC=200,Determine(i) Collector emitter voltage (VCE) (ii) Collector current (IC)
1. Determine Vpout for the circuit in below and draw Vauts assume the diode is the silicon type. 10 k +10 V-- V. ov R, 100 k IN914 -10 V- 2. What is the output voltage that you would expect to observe across R, circuit of Figure below? Assume that RC is large enough to prevent significant capacitor discharge. +24 V 10 uF RL 10 kn V. ov. IN914 -24 V
Assuming an ideal diode model for all the diodes in the circuit below, chose the correct state (bias) for each diode. R1 ww 9kQ 1N1199C R2 D1 18kQ 1N1199C V2 12 V R3 1kQ D3 1N1199C R4 D3: On (Forward Bais) D3: Off (Reverse Bais)
A stabilization circuit has a stability factor of 0.04 and an internal resistance of 5 2. The unstabilized voltage can vary between 75 and 100 V, and the load current can vary from 40 to 80 mA. Determine the maximum and minimum values for the stabilized load voltage.
In the circuit shown below, R1 = R2 = 200Q, and the two diodes are identical with VD = 0.7V and Vps =5V. 1. Find output voltage Vo. 2. Find I1, I2, Ipi and Ip2. R1 www Vo Ipi Ip2 Vps
a2/a.Design Circint as the following pescripton: A- the positive Cyycle of the vout signal is 3.2 and Negate cycle is 4-3 (Note: we must used preetical Diodes and vin is tov) 1B- the positive cycleg of vout is 5-3 and Negative cycle is (5. 4) [note: consider tovavd we must used Cupaetor with praetical Drade) Vin اضف ملف
For each circuit, use the diode approximation with the forward drop equal to 0.7 V and determine Vout. +3 V 10 k - Vout -3 V ++3 V 10 k - Vout -3 V ++3 V 10 k 5 k -3 V Vout
B. For the circuit shown below, assume that the zener diode has Vz-3.3V and rz=092 when reverse biased, and has a 0.7V drop when forward biased. Fill the following table for values of Vo for different values of input voltage Vi. R1 Vi Vi -8V OV 8V 1k 5V N V2 R21k Vo Vo
The 4-layer diode in the circuit is biased such that it is in the forward- conduction region. Determine the anode current for and VBR(F) = 20 V, VBE = 0.7 V, VCE(sat) = 0.2 V. VAS 30V R₂ ww K V-20V 1-4mA