2. Three Unbalanced loads connected in wye configuration and is impressed by a balance three phase, four-wire source. The per phase voltage of the source is 230V. Assume phase voltage A as reference, determine the line currents Ia, Ib and Ic and the neutral current if the following unbalance loads are: Load an: 30kW at 0.8 lagging power factor Load bn: 50kW at 0.6 lagging power factor Load cn: 30 kW at 0.9 leading power factor.

2. Three Unbalanced loads connected in wye configuration and is impressed by a balance three phase, four-wire source. The per phase voltage of the source is 230V. Assume phase voltage A as reference, determine the line currents Ia, Ib and Ic and the neutral current if the following unbalance loads are: Load an: 30kW at 0.8 lagging power factor Load bn: 50kW at 0.6 lagging power factor Load cn: 30 kW at 0.9 leading power factor.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw the power factor triangle showing the different labelled sides. Illustrate a lagging power factor using a sinusoidal waveform. (d) List 2 negative effects of a poor power factor (e) How can a lagging power factor be corrected?
The single phase AC sinusoidal voltage then the rms value of the voltage v is .........
Another name for the RMS value of current or voltage is ... O the effective value O the exact value O the true value O the reactance value
5. Two ac sources feed a common variable resistive load as shown in figure. Under the maximum power transfer condition, the power absorbed by the load resistance RL is? 11020° 602 w 18.0 m 652 802 Mm 9020°
Q.6/ Modify the sawtooth generator in figure below so that its peak-to-peak output is 4V. Is it aVCO?
Which one of the following statements is true: The purpose of the power-factor correction is to add inductive elements to keep real power at a minimum level. The purpose of the power-factor correction is to add resistive elements (typically resistances) to improve the total reactive power. The purpose of the power-factor correction is to add reactive components (typically capacitive) to establish a system power factor closer to unity. The purpose of the power-factor correction is to add resistive elements (typically resistances) to establish a system power factor closer to zero.
Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average and RMS for both currents. a = 50° T1 50 2 ot Vs = 300 sin 100rt T2 ot
Clear and correct or dislike
Solve for 20 V rms supply. Thank you.
i need the answer quickly
Computed Rms value (V) 100 E1:A to B E2:A to C 1502 E3:A to D 220. E4:A to F 220 Vac E5:A to G 330 E6:F to G E7:B to C 470 E8:C to D 6802 E9:D to E E10:E to F
2. Three series loads are drawing 20A ms current through a 60HZ source. Load 1 is an 400W, 0.8 lagging induction motor. Load 2 is a 500VA, 0.6 lagging power factor and load 3 is a 2 ohm incandescent bulb. a) What is the total VA of the combined load? b) What is the overall PF of the combined load? c) What RMS voltage is the combined load operating? d) What capacitor VAR must be installed in parallel to the combine load to improve its overall PF to unity? e) What is its approximate capacitance in microfarad?