2. The type of air cycle used in diesel engine is called a. Otto cycle b. Carnot cycle c. Diesel cycle d. Rankine cycle Ans: c 3. During suction stroke the pressure inside the cylinder is a. Equal to atmospheric pressure b. Above atmospheric pressure c. Above or below atmospheric pressure d. Below atmospheric pressure Ans: d 4. During compression stroke the air is compressed according to a. Isothermal process b. Hyperbolic process c. Adiabatic process d. Constant pressure process Ans: c

2. The type of air cycle used in diesel engine is called a. Otto cycle b. Carnot cycle c. Diesel cycle d. Rankine cycle Ans: c 3. During suction stroke the pressure inside the cylinder is a. Equal to atmospheric pressure b. Above atmospheric pressure c. Above or below atmospheric pressure d. Below atmospheric pressure Ans: d 4. During compression stroke the air is compressed according to a. Isothermal process b. Hyperbolic process c. Adiabatic process d. Constant pressure process Ans: c

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a) State all four processes that make up the Otto air standard cycle. b) Sketch the cycle on a P-V diagram. c) Prove that the cycle efficiency is given as follows where, r = compression ratio Y = specific heat ratio notto = 1 - 1 ry-1
c) In an air standard diesel cycle, the pressure and volume of beginning of compression are 200 kPa and 0.05 m respectively. Pressure after isentropic compression is 5.2 MPa and isentropic expansion is 400 kPa. Determine compression ratio, cut-off ratio, expansion ratio, cycle efficiency.
Describe in your own words the operation of a petrol engine, and explain how it is estimated by the idealised Otto cycle. [Hint: you can make use of one or more diagrams.]
A gas turbine power plant working on Brayton cycle as per the following specifications Pressure and temperature of air at inlet to compressor = 1 bar and 10oC Power output of the plant = 8 MW Temperature at inlet to the turbine = 780 oC Pressure ratio = 12 Isentropic efficiency of compressor = 100% Isentropic efficiency of turbine = t(%)= 91 Perform the following: 1) Pressure, specific volume and temperatures at all the points of the cycle? 2) Mass flow rate required?
In 4-stroke Cl engines, the ignition induced by O hot coolant. O lubrication oil. O exhaust valve. O fuel tank. O spark plug. O high temperature due to high pressure ratio.
Describe how actual internal combustion engine cycle(i.e. Otto and Diesel)thermal efficiency differ from the ideal one at the same power output.
What are the difference between jet cycle and open Brayton cycle.
(1): We can classify IC engine into two categories on the basis of number of stroke for each cycle. Two stroke engine: In two stroke engine suction and compression takes place in 180 degree rotation of the crank which is counted as one single stroke and power and exhaust stroke takes place during the second stroke of the engine. Four stroke engine: In four stroke engine all the four processes takes place with different different strokes so total angle of rotation of the cranks will be 720 degree which consists of two full rotation of the crank.
Which of the following statement is not true of the diesel cycle? (you must use thermodynamic diagram with explanation.)a. The expansion process is an isentropic process.b. The exhaust process is a constant-volume process.c. The combustion process is a constant-volume process.d. The compression process is an adiabatic process.e. One heat transfer process is a constant-pressure process
Chose the correct anser 7. The efficiency of Carnot cycle depends upon a. temperature limits b. pressure ratio c. volume compression ratio d. cut-off ratio and compression ratio 8. The compression ratio is the ratio of a. swept volume to total volume b. total volume to swept volume c. swept volume to clearance volume d. total volume to clearance volume 9. The ratio of isothermal power to actual measured input power of a compressor is known as: a. Isothermal efficiency b. Volumetric Efficiency c. Barometric efficiency d. None 10. The part use for heat rejection in the Rankine Cycle is: a. Turbine b. Boiler c. d. Pump Condenser
Mechanical EngineeringThermodynamicsTopic: Rankine Cycles
Thermodynamics subject power cycles. Show the ts diagram and complete and step by step solution. Box the final answer.