2. The rig shown consists of a 1200-lb horizontal member ABC and a vertical member DBE welded 75 17.5 together at B. The rig is being used to raise a 3600-lb crate at a distancex 12 ft from the vertical member DBE. If the tension in the cable is 4 kips, determine the reaction at E, assuming that the cable is anchored at Fas shown in the figure. 65R W-100 3600 I

2. The rig shown consists of a 1200-lb horizontal member ABC and a vertical member DBE welded 75 17.5 together at B. The rig is being used to raise a 3600-lb crate at a distancex 12 ft from the vertical member DBE. If the tension in the cable is 4 kips, determine the reaction at E, assuming that the cable is anchored at Fas shown in the figure. 65R W-100 3600 I

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Moving to another question will save this response. Question 1 Which of the following statement is NOT correct? Fluid Mechanics is the study of the behaviour of fluids. Fluid Mechanics is the study of the behaviour of solids. Fluid Mechanics is the study of the behaviour of liquids. Fluid Mechanics is the study of the behaviour of gases.
B3
This answer was marked incorrect
The answer should be 24,6kN when rounded up.
HANDWRITTEN. answer 4 5 6 then box the final answers
A sprinter practicing for the 200-m dash accelerates uniformly from rest at A and reaches a top speed of 36 km/h at the 76-m mark. He then maintains this speed for the next 61 meters before uniformly slowing to a final speed of 31 km/h at the finish line. Determine the maximum horizontal acceleration which the sprinter experiences during the run. Where does this maximum acceleration value occur? Part 1 Answers: (a) al- Finish line Calculate (a) the magnitude of the tangential acceleration near start of the race and (b) the magnitude of the tangential acceleration near the end of the race. (b) lal- i 0.658 i 0.205 m/s² 39.9 m m/s² A Save for Later Last saved 12 minutes ago. Saved work will be auto-submitted on the due date. Auto- submission can take up to 10 minutes. Attempts: 0 of 3 used Submit Answer Part 2 The parts of this question must be completed in order. This part will be available when you complete the part above.
The open tank shown, which has a liquid with a specific gravity of S=127 as shown in the give figure, is accelerated upward at one g what is the pressure at point 1(kpa)? 150 cm 190 mm
If a critical point at structural element is subjected to the stress shown on the 2D element, determine the factor of safety (FS) against rupture according to the maximum principal stress theory. The material has an ultimate tensile stress Sult = 500 Mpa. 150 Mpa 50 Mpa 250 Mpa
I need these three parts answered (Multiple Choice). If you can not answer all three parts please leave it for another tutor to answer. Thank you. For the two holes identified as datum D, what is the total size tolerance specified for those holes? (Multiple Choice)a. .002'b. .003'c. .004'd. .006' The two holes identified as datum D have a counterbore on one end. What size toleranceis specified for the counterbore diameter? (Multiple Choice)a. .010″ (±.005″; see title block)b. .020″ (±.010″; see title block)c. .030″ (±.015″; see title block) What letter represents the revision status of this print? (Multiple Choice)ABCD
Pls do stepwise and correct.
d) Determine the factor of safety n. Enter your answer to 2 decimal places.
Question 1