2. The results of Marshall Test for five specimens are given below. Find the optimum bitumen content for the mix. Bitumen Stability Flow Vv VFB Gm content (kg) (units) (%) (%) 3.5 510 9.0 12.5 34 2.17 4 700 9.5 7.2 65 2.21 4.5 815 11.5 3.9 84 *2.26 5 770 15 2.4 91 2.23 5.5 660 19 1.9 93 2.18

2. The results of Marshall Test for five specimens are given below. Find the optimum bitumen content for the mix. Bitumen Stability Flow Vv VFB Gm content (kg) (units) (%) (%) 3.5 510 9.0 12.5 34 2.17 4 700 9.5 7.2 65 2.21 4.5 815 11.5 3.9 84 *2.26 5 770 15 2.4 91 2.23 5.5 660 19 1.9 93 2.18

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the longitudinal Ultrasonic Pulse Velocity of a concrete mixture was measured as 4000 m/s, and the specific gravity and the Poisson's ratio of this concrete mixture are known to be 2.4 and 0.20, respectively, what is the dynamic elastic modulus this concrete sample? O a. 34.6 GPa O b. 25 MPa O C. 350 MPa O d. 25 GPa Oe. 34.6 MPa
Find.,
Q- In a Marshall sample, the bulk specific gravity of mix and aggregates are 2.324 and 2.546 respectively. The sample includes 5% of bitumen (by total weight of mix) of specific gravity 1.10. The theoretical maximum specific gravity of mix is 2.441. The void filled with bitumen (VFB) in the Marshall sample (in %) is
Sieve analysis of a sample of fine aggregate resulted in the following data No. Sieve number 4 8 16 30 50 100 Sieve opening (mm) 4.75 2.36 1.18 0.6 0.3 0.15 Weight retained (g) 13 75 120 126 105 61 A) The total weight of the sample, assuming no mass loss during the analysis, is______ (g) a) 505; b) 500; c) 550 B) The half sieve used in the experiment is________. a) No.8; b) No.50; c) none of the above C) The fineness modulus of the aggregate________. a) 6.13; b) 3.16; c) 1.36 D) The average size of the aggregate___________. a) No.30; b) No.4; c) No.16
Design of a concrete mix showed that 1 m3 of the mix contains 320 kg cement, 540 kg sand. A trial mix having the same proportions as the designed mix, enough for 6 standard cubes, containing 3.5 liters water was made. It is required to calculate the quantities by weight and volume for the construction of a concrete road having 25 m width, 1000 m long, and 0.25 m thick, given that the trial mix gave slump and compressive strength as designed.Specific density of cement = 3.15Specific density of aggregate (coarse or fine) = 2.7Unit weight of cement = 1440 kg/m3Unit weight of sand = 1600 kg/m3Unit weight of gravel = 1760 kg/m3 Using BSI Method Only
Workability of concrete is measured in a concrete lab by compaction factor test. If the partial compacted concrete weight after deducting empty weight of cylinder 11.4 kg and fully compacted concrete weight after deducting empty weight of cylinder = 11.98 kg. Determine. compaction factor value. O a. 11.69 O b. 0.58 O c. 0.95 C. O d. -0.86 =
What must be the minimum size (width) of chutes of the mechanical splitter if the dry fine aggregate sample passes 9.5mm sieve?
The specific gravity and absorption test (ASTM C128) were performed on fine aggregate. The following data were obtained.Given:Mass of SSD sand = 400.0 gMass of pycnometer with water = 520.0 gMass of pycnometer with water plus sand = 850.0 gMass of dry sand = 397.0 gRequired:a) bulk dry specific gravityb) bulk SSD specific gravityc) apparent specific gravity aaaaaaaaaa
Problem #1 The following figure shows the results from the dynamic modulus test for asphalt mixtures. The specimen is 4" in diameter and 6" in height. The gauge length for the axial LVDT is 4". Time lag is 0.25s. Find |E*I, and phase angle . Axial force(lbf) 65 60 40 20 0 -20 -40 -65 0 Dynamic modulus test result (gauge length = 4") 0.5 Time (second) 1 0.0010 0.0009 0.0006 0.0003 0 force (lbf) disp (in.) -0.0003 -0.0006 -0.0009 -0.0010 1.5 Axial displacement(in) 4"
Problem- A mix contains coarse aggregate, fine aggregate and mineral filler in proportion 60:35:5 by weight and their respective specific gravities are 2.7, 2.9 and 1.5 .These materials were mixed with bitumen of specific gravity 1.01 and compacted to unit weight of 2300 kg/m³ having 5% voids. How much %age bitumen does the specimen contain?
02-In the laboratory, 6 cubes (0.07 0.07 0.07) m were tested for compressive strength for ordinary portland cement. The results were recorded as shown in table below. Find the compressive strength of the sample for (3.7) day and compare with the Iraqi Specification (M.q.a No. 1984/5). Cube No. Force caused failure (KN)-3 days) Force caused failure (KN)-7 days I 2 62 64 95 97 3 69 93