2. The orthographic view shows the part from Sides. Select one: a.4 O b.2 c.3 d.1

Q: 50. The movement of the cutter of the shaping machine over the work is called Select one: a.COURSE…

A: Course is a term associated with feed. Crank is a rotating link of the shaper mechanism.  Travel is…

Q: A chain of home health care firms in Selangor needs to locate a central office from which to conduct…

A: Consider the frequency table shown below for the given coordinates.

Q: 34. The operation of removing material from the end face of a round shaft is .ROwww Select one:…

A: Facing is the process of removing metal from the end of a workpiece to produce a flat surface

Q: 37. The operation of removing material with a multi-teeth circular cutter from the surface of a…

A: Drilling- It is a cutting (material removal ) process in which drill bit which is a rotary cutting…

Q: What are the benefits of adopting these standards by an industrial organization?

A: Benefits of adopting standards by an industrial organization are: Less wastage. Globally recognized…

Q: Determine the magnitude of the force (in N) of the y-component of the internal pin at B.

A:

Q: Exoskeletons (which may also be referred to as exosuits, exosystems, industrial human augmentation,…

A: To explain:Evaluate the following alternatives based on your criteria, and justify your selection…

Q: Perform FMEA and Root Cause Analysis for any TWO problems faced in your industry.

A: introduction; FMEA is a failure mode and effect analysis. FMEA quality tools enhance the quality of…

Q: 26. When a two-fluted end mill is used to cut a slot, the maximum depth of cut should be Select one:…

A: Option a is correct.

Q: A construction site has machines that simultaneously excavate and grade Machine A grades: G = 17.8…

A: Let us make a table of the given data as shown below - The total amount of grading to be done = 100…

Q: solve this reliability exercise pls

A: For a constant failure rate λ(t) = λ:Reliability Function: R(t) = e^(-λt)Cumulative Distribution…

Q: 63. The process of impression a diamond-shaped or straight-line pattern into the surface is called…

A: Knurling is a manufacturing process, typically conducted on a lathe, whereby a pattern of straight,…

Q: Q) The following particulars refer to a screw jack, Diameter of screw rod = 62.5 mm Length of the…

A: The solution is given in below step

Q: 28. The most commonly used grinding wheels are made from Select one: a.SILICON CARBIDE b.DIAMOND…

A: Aluminum oxide is the most common abrasive used in grinding wheels.

Q: 50. The movement of the cutter of the shaping machine over the work is called Select one: a.COURSE…

A: Generally shaping machine has two strokes they are 1. Cutting stroke or forward stroke 2. return…

Q: Which of the following distinguishes why farms account for so many injuries of children in the…

A: Farming is considered as a family business and the children working on their parents' farms are…

Q: A Carnot cycle using 60 kg min of water, is applied to generate electrical power (at the turbine,…

A: Carnot cycle The Carnot cycle is the ideal thermodynamic cycle. In Carnot cycle there are four…

Q: 69. Which of the following instrument is used for angular measurement? Select one: a.COMPARATOR…

A: A sine bar is used in conjunction with slip gauge blocks for precise angular measurement

Q: 17-The surface roughness is shown with a symbol.... a) Ra b) Rs c) Rc d) Rq 18- The largest diameter…

A: As it is not mentioned that which three parts required to solve, please find the solutions of first…

Q: Give at least 7 possible safety concerns and design solutions made by an industrial hygienist that…

A: Manufacturing is the creation or manufacturing of items using equipment, manpower, machinery,…

Q: Solve the fallaning equations to oR y+y = 24e 8.caszt +44= sec2x

A:

Q: MENG30 Please solve the problem by keupord 10.Consider the Material Selection Design Problem for the…

A: To solve:Consider the Material Selection Design Problem for the FRAME of a Human Powered Road…

Q: 15. Files are usually made of Select one: O a.LOW CARBON STEEL b.HIGH CARBON STEEL O c.MEDIUM CARBON…

A: Steel files are made from high carbon steel (1.0 to 1.25% carbon) and may be through hardened or…

Q: For the engineering activity, current practical capacity is defined by the following requirements:…

A: C (current practical capacity in engineering hours) is defined by the following requirements: 6000…

Q: 70. The method of joining the two pieces together by melting a small area and allowed to fused…

A: Solution:

Q: 14. Which of the following procedures would be correct to mark the center of a hole location? Select…

A: The centre punch tool is a special type of punch tool used to create a shallow indentation in a…

Q: The worker shown below is driving 4 screws into a panel with a powered driver. His production quota…

A: Disclaimer: Since you have asked multiple questions, we will solve the first question for you. If…

Q: skating is an example of

A: Answer:- sliding friction

Q: 69. Which of the following instrument is used for angular measurement? Select one: a.COMPARATOR…

A: A sine bar is used in conjunction with slip gauge blocks for precise angular measurement.

General safety guidelines

Safety guidelines are the set of rules and codes that must be followed in the workplace for the occupational safety of workers, the machines, and the equipment that are present inside the workshop premise. There are many unsafe conditions and hazardous materials inside the workshop that makes prey for certain risk factors associated with health conditions. Extreme safety precautions must be taken inside the work area just like the precautions and practices that are been followed for Corona Virus Disease 2019 (COVID-19). People can also educate themselves by joining various health programs and camps. These will provide them with the necessary skills and knowledge about safety awareness. Occupational Safety and Health Administration (OSHA) thrives to create a safe and healthy environment for the workers working in the industries and provides them with proper education and training.