2. The air pressure in the top of the 2-liter pop bottle shown in Fig. below is 40 psi, and the pop depth is 10 in. The bottom of the bottle has an irregular shape with a diameter of 4.3 in. (a) If the bottle cap has a diameter of 1 in. what is the magnitude of the axial force required to hold the cap in place in Ibs? (b) Determine the force needed to secure the bottom 2 in. of the bottle to its cylindrical Sides in Ibs. For this calculation assume the effect of the weight of the pop is negligible. (c) By how much does the weight of the pop increase the pressure 2 in. above the bottom in Ibs? Assume the pop has the same specific weight as that of water.

2. The air pressure in the top of the 2-liter pop bottle shown in Fig. below is 40 psi, and the pop depth is 10 in. The bottom of the bottle has an irregular shape with a diameter of 4.3 in. (a) If the bottle cap has a diameter of 1 in. what is the magnitude of the axial force required to hold the cap in place in Ibs? (b) Determine the force needed to secure the bottom 2 in. of the bottle to its cylindrical Sides in Ibs. For this calculation assume the effect of the weight of the pop is negligible. (c) By how much does the weight of the pop increase the pressure 2 in. above the bottom in Ibs? Assume the pop has the same specific weight as that of water.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pressure gauges G, and G, installed on the system show pressure of PG1 = 5.00 bar and PG2 1.00 bar. The value of unknown pressure Pis [Atmospheric pressure = 1.01 bar] = P G₁ G₂
The pressure gauges G, and G, installed on the system show pressure of PG1 = 5.00 bar and PG2 1.00 bar. The value of unknown pressure Pis [Atmospheric pressure = 1.01 bar] = P G₁ G₂
A glove box is an enclosure held at a lower pressure than its surroundings to ensure that any fluid that escapes its container within the glove does not escape into its surroundings. The pressure inside a sealed container sitting in the laboratory is 7.3 psig when the pressure in the laboratory is 14.8 psia. a) What is the absolute pressure inside the container? b) What is the gage pressure inside the container when it is inside a glove box maintained at a pressure of 13.5 psia? PABS = PGAGE= psia psig
len10
A glove box is an enclosure held at a lower pressure than its surroundings to ensure that any fluid that escapes its container within the glove does not escape into its surroundings. The pressure inside a sealed container sitting in the laboratory is 7.1 psig when the pressure in the laboratory is 14.4 psia. a) What is the absolute pressure inside the container? b) What is the gage pressure inside the container when it is inside a glove box maintained at a pressure of 12.9 psia? PABS= PGAGE= psia psig
If the bottom of a pop bottle similar to that shown in the figure below, what would be the magnitude of the resultant force acting on the hemispherical bottom? The air pressure in the top of the bottle is 38 psi, and the pop has approximately the same specific gravity as that of water. Assume that the volume of pop remains at 2 liters. R= D -Pair = 38psi 4.3 in. diameter
For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal pressure of 15MPA, d is the inside diameter of the container of 20mm, and t is wall thickness of 10mm. See figure 103. For question 103B, the girth stress is equal to Girth joint Longitudinal joint Figure 103 15 MPa 7.5 MPa 3.75 MPa О 30 МРа
2.52 A water column in a glass tube is used to measure the pres- sure in a pipe. The tube is 1/4 in. (6.35 mm) in diameter. How much of the water column is due to surface-tension effects? What would be the surface-tension effects if the tube were 1/8 in. (3.2 mm) or 1/32 in. (0.8 mm) in diameter?
For a 2mm diameter glass tube which is inserted in water at 15°C, as shown in the figure 1 below. Determine the height that the water will climb up the glass tube. Please note that the water makes a contact angle of 0° with the clean glass.
7. In the figure shown, determine the value of z when the pressure at A is 10 psi greater than at B. water 2fti Hg A 6 ft B
2. Find the surface tension in N/m in a soap bubble of 30 mm diameter when the inside pressure is 1.962 Pa above atmosphere. A. 0.00325 B. 0.00465 C. 0.00735 D. 0.01325
Pipe 1 which is 100 mm in diameter and 350 m long is in parallel to pipe 2 which is 300 m long. Pipe 1 carries 90 liters per second while pipe 2 carries 160 liters per second. What is the diameter of pipe 2 if the friction factor for both pipes is the same? Select one: O a. 156 mm O b. 135 mm O c. 122 mm O d. 168 mm