2. Please complete the table below. Please fill the name of the phases after the indicated heat treatment. Phases before Cooling speed or heat Phases after heat treatment heat treatment treatment process Pearlite Slow / Annealing Pearlite Austenite Moderate cooling Austenite Quenching Austenite Quenching + Tempering

2. Please complete the table below. Please fill the name of the phases after the indicated heat treatment. Phases before Cooling speed or heat Phases after heat treatment heat treatment treatment process Pearlite Slow / Annealing Pearlite Austenite Moderate cooling Austenite Quenching Austenite Quenching + Tempering

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use the copper silver phase diagram below. 100g of a 40 wt% Cu 60 wt% Ag alloy is made and cooled from liquid form. a. At what temperature does the solid phase start to appear? b. What phases exist at 780°C? c. What are the compositions (Cu and Ag%) of the phases in question b? d. What are the weights (in g) of Cu in the solid phase and liquid phase in question b?
L.Grain size reduction II. Solid solution strengthening II. Age hardening IV. Cold working V.Dispersinion hardening Strengthening mechanism for single phase metals is/are
(c) The steels with the following compositions are heat treated and the results of microstructures are indicated in Table 2(c). Table 2(c): Heat treated steels and the results of microstructures Steel A 0.35 wt% C Coarse Pearlite Steel B 0.25 wt% C Coarse Pearlite Steel C 0.35 wt% C Fine Pearlite Rank the above steels based on carbon content and microstructures from the highest to the lowest hardness with justification.
A 50 wt% Pb-50 wt% Mg alloy is slowly cooled from 700 °C (1290 °F) to 400 °C (750 °F). (a) At what temperature does the first solid phase form? (b) What is the composition of this solid phase? (c) At what temperature does the liquid solidify? (d) What is the composition of this last remaining liquid phase? Temperature (°C) 700 600 500 400 300 200 100 2 0 0 (Mg) 560°C First solid (21 wt% Pb) α 20 465°C 5 a + L Composition (at% Pb) 40 10 L a + Mg₂Pb 20 60 Composition (wt% Pb) Last liquid (67 wt% Pb) 30 Mg₂Pb 40 T T L + Mg₂Pb M 18 80 L + Mg₂Pb 70 100 B B+ Mg₂Pb T B + L D T 1200 1000 800 600 400 200 100 (Pb) Temperature (°F)
1. Given the time-temperature transformation diagram, what would be the phases present for a 1.13 wt. % C steel with no alloying elements. calculate the amount of pro eutectoid product, where applicable (at the bottom) A) quenched in cold water to 650 C in 0.1 seconds, then held at 650 C for 5 seconds, then quenched to 400 C, held at 400C for 60 seconds, and finally quenched to room temperature B. Necessary Steel Phase Diagram Calculations to determine the amount of pro eutectoid product:
Answer ASAP
Using the isothermal transformation diagram given in Figure 2 for a specific material composition to answer the following (this is NOT an Fe-C steel!). NOTE: Assume that you begin with a single-phase sample of α at 790 C.a. What temperature on the diagram corresponds to the α-to-γ phase transformation temperature that would be found on an equilibrium phase diagram? Explain your answer. b. What temperature would provide the most rapid, isothermal phase transformation of α to γ? What would be the minimum time from onset of the phase transformation to its completion? c. On Figure 2, draw and label a cooling schedule (from 790 C) that will produce a single-phase α material at 100 C. How does the thickness of the piece of material influence your ability to create a single-phase α structure? d. Why does the time to initiate phase transformation become smaller as the temperature is reduced within the temperature range above the “nose” of the TTT diagram? Be specific, what process is…
Material science Assuming this system forms a laminar type eutectic, determine the volume proportion of phases for an equilibrium solidified 50% Pb alloy. Sketch the expected microstructure.
Bainite phase and pearlite phase have different mechanical properties due to its structure differences. Discuss the hardness and tensile strength of these 2 phases using isothermal transformation temperature diagram.
Consider 2.0 kg of austenite containing 0.5 wt% C and cooled to just below 727°C (1341°F). (a) What is the proeutectoid phase? (b) How many kilograms each of pearlite, the proeutectoid phase, and cementite form?
1) Draw the iron-Fe;C phase diagram. Consider 0.25 and 1.1 wt% C steel alloy. It is cooled slowly from atemperature within austenite phase to room temperature. Show a) microstructure at 1000 °C b) microstructure at 730°C c) microstructure at 715°C and d) microstructure at room temperature e) What do you say about mechanical properties of these alloys, depending on their microstructure at room temperature?