2. Locate the centroid (x, y) of the metal cross section. Neglect the thickness of the material and slight bends at the corners. (Hints: Consider symmetry. Use line segments. You may treat the upper circular section as one uniform half circle. Ignore the length of the arches.) 50 mm. 50 mm 100 mm 100 mm 50 mm plz show all the work 150 mm

2. Locate the centroid (x, y) of the metal cross section. Neglect the thickness of the material and slight bends at the corners. (Hints: Consider symmetry. Use line segments. You may treat the upper circular section as one uniform half circle. Ignore the length of the arches.) 50 mm. 50 mm 100 mm 100 mm 50 mm plz show all the work 150 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Compute the coordinates of the centroid (î, g) of the area shown. Also compute the area moment of intertia about the r' and y' axes with origin at the centroid. 2013 Michael Swanbom cc BY NC SA a k-d Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 14 mm 111 mm 12 mm d 45 mm h 89 mm w 22 mm The z coordinate of the centroid is a = mm. The y coordinate of the centroid is j mm. The moment of inertia about the z' axis going through the centroid is Iz mm. The moment of inertia about the y' axis going through the centroid is Iy = mm*.
Determine the locationof the centroid for the cross-section shown below and draw a scaled sketch of the cross-section, clearly showing the centroid and indicate its distance from the selected origin. (Start your calculations be setting an origin from the bottom, left-most point on the cross-section). 2 Calculate the second moments of areas about the centroidal axes for the beam cross- section. 60 mm |10 mm 10 mm 100 mm 10 mm 40 mm
please box in the following answers: normal stresses for beam AB and BC (mid section) normal stresses for beam AB and BC (at connections A and C) shear stress for pin A, B and C bearing stress along member AB and BC at pin section for A and C 600mm Flat end 40 mm FRONT VIEW d-25 mm d-25 mm 50 mm 125 mm 30 mm 25mm ,20 mm TOP VIEW OF ROD BC -800 mm Q-30 kN TOP VIEW OF BOOM AB d=25mm Flat end Q-30KN 20mm 20 mm END VIEW 600 mm 50 mm 20 mm 800 mm 30 AN 1
Determine the state of stress of a beam at the point shown in Figure 2 to represent: a) the principal stresses; b) the maximum in-plane shear stress and the associated average normal stress. c) For each of the two cases mentioned in (a) and (b), determine the corresponding orientation of the element with respect to the original element shown and sketch the results relative to the longitudinal axis of the beam. Please show the full working to provide sufficient information for the sketching to be complete. 15MPa Figure 2 20° 50MPa
Compute the coordinates of the centroid (i, g) of the area shown. y y = a /bx Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 4.5 in 2 in'1 (Note the -1 exponent only applies to the unit, not the number.) 7 in The a coordinate of the centroid is = in. The y coordinate of the centroid is ỹ = in.
The steel bar has the original dimensions shown in the figure. (Figure 1) It is subjected to an axial load of 50 kN. E=203 GPa, Va 0.30. Figure 1 of 1> 50 kN -60 mm - 20 mm 20 mm 200 mm 20 mm 350 mm 50 mm s0 kN 200 mm
The 2 X 12 joist shown in Figure has an Ixx value of 178 in.“. What will be the percentage decrease in this value if a hole 2 in. in diameter is drilled through it at location A? 1.5 A 11.25 11 25 2.
Explain the absolute maximum shear stress. Construct Tresca’s hexagon by explaining all the points on the figure shown belo
6) Find the centroid, (x, 5), of the area below. The circle and semi-circle are holes. The circle has a diameter of 0.5 m, is tangent to the x-axis, and is centered with the x = 0.5 m mark. The semi-circle has a radius of 0.15 m and is centered with the x = 1.5 m mark. y2 = x -y +x = 2 1 m 1m 1 m
The AB part of the rod is steel and is 100mm in diameter.The BC part of the rod is copper and its diameter is 80 mm. a)Draw the normal force diagram of the rod. b)Calculate the normal stresses in sections AB and BC. c)Calculation of the total length change of the bar.
The figure shows the chain drive of a bicycle. How far will the bicycle move if the pedals are rotated through 180°? Assume the radius of the bicycle wheel is 12.7 inches. The bicycle will travel approximately (Round to the nearest tenth.) in. C -1.95 in 4.21 in