2. In the network shown, given ɛ = 36 V, R1 = 40, R2= 6.000 and R3=3.00n.What is the potential difference difference Vab between points a and b when theswitch S is open and when closed?R3%3DR1Calculate the current through all resistors at open and closed switch S.What happens to the current for each resistor if S is closed? Does it increase orR2decrease?

To solve above question, concepts required are: Kirchhoff's law: There are two Kirchhoff's law.KCL:…

2. In the network shown, given & = 36 V, R = 40, R2= 6.000 and R3=3.00n. What is the potential difference difference Vab between points a and b when t switch S is open and when closed? R1 R1 ww Calculate the current through all resistors at open and closed switch S. What happens to the current for each resistor if S is closed? Does it increase decrease? R2

2. In the network shown, given & = 36 V, R = 40, R2= 6.000 and R3=3.00n. What is the potential difference difference Vab between points a and b when t switch S is open and when closed? R1 R1 ww Calculate the current through all resistors at open and closed switch S. What happens to the current for each resistor if S is closed? Does it increase decrease? R2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

pls answer in 3 decimal places & box your answer
Using the circuit below with R1 = 1 kQ, R2 = 10 kQ, and E = 9 volts, determine the theoretical voltages at points A, B, and C with respect to ground. Record these values. Apply Ohm's law to determine the expected currents through R1 and R2. Record these values. Include demonstration of Kirchhoff's Voltage Law. A В -E R1 I, R2 2 Ground
The circuit shown below is an example of a simple voltage regulator. Determine the current through R2 in mA. Assume the following values for the resistors: R1 = 13 kn, R2 = 10 kn. Express your answer using three decimal places. Assume the opamp is ideal and Q1's B is infinity. Q1 VCC Vref NPN U1 OUT 20V 1.2V R1 R2 + +
Using the figure, determine the currents I1, I2, and I3. The batteries have electromotive forces (emfs) of Ɛ1 = 9.0 V, E2 = 12.0 v, and Ɛz = 6.0 V. The resistors have values R1 = 25 2, R2 = 48 N, and R3 = 30 N. R1 E1 E2 I2 R2 R3 E3 I3
Three resistors are connected in parallel namely R1, R2 and R3. It is impressed by a source voltage of 120V. If R1 receives 15W while R2 carries a current if 100mA, what should be the value of resistance R3 if the power supplied by the voltage source is 60W? a. 364.4 ohmsb. 436.4 ohmsc. 43.64 ohmsd. none of these
The Subject is Basic Electrical Engineering Chapter 5. Connection of Resistor Connection of Resistors
V = 36 V Refer to the figure at the right. iz What is the potential of point a with respect to point b when switch S is open? 3 0 What is the current through switch S S When it is closed? What is the equivalent resistance of this combination of resistors when S is closed?
4. Verify Kirchhoff's junction rule by measuring current flows at the junction a. Write induvial values and sum them up to show conservation of charge. R1 R3 a R4 {I R2 I1 €1 b 13 €3 12 €2 Circuit 4
A 12.0 V battery with internal resistance r is connected to two parallel resistors as shown in the figure below. The current through the 3.00 Ohm resistor is measured to be 200. mA. 8 = 12.0 V R1 = 12.0 2 ww ww R2 = 3.00 2 Question 2 Find the drift velocity of electrons in the 3.00 Ohm resistor in mm/s.
FIND CURRENT FLOWING THROUGH Z1FIND CURRENT FLOWING THROUGH Z2FIND CURRENT FLOWING THROUGH Z3FIND CURRENT FLOWING THROUGH Z4FIND CURRENT FLOWING THROUGH Z5FIND CURRENT FLOWING THROUGH Z6FIND CURRENT FLOWING THROUGH Z7Total Ampere supplied by V1Total Ampere supplied by V2
Consider the circuit in the given figure. Assume R1 = 120 S and R2 = 260 N. R R2 40 V Calculate current i in the given figure when the switch is in position 1. The current when the switch is in position 1 is mA.
TOPIC: Combination Circuit. SHOW THE SOLUTIONS