2. In a fully developed pipe flow, Pressure increases along the direction of the flow 22 Axial velocity do not change Radial velocity is maximum at the center Pressure linearly decreases along the direction of the flow Axial velocity grows linearly Pressure exponentially decreases along the di- rection of the flow Flow is laminar

2. In a fully developed pipe flow, Pressure increases along the direction of the flow 22 Axial velocity do not change Radial velocity is maximum at the center Pressure linearly decreases along the direction of the flow Axial velocity grows linearly Pressure exponentially decreases along the di- rection of the flow Flow is laminar

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Mechanical-Energy Balance and Friction Losses. Hot water is being discharged from a storage tank at the rate of 0.223 ft3/s. The process flow diagram and conditions are the same as given in Example 2.10-6, except for different nominal pipe sizes of schedule 40 steel pipe as follows. The 20-ft-long outlet pipe from the storage tank is 1 1/2 in. pipe instead of 4-in. pipe. The other piping, which was 2-in. pipe, is now 2.5-in. pipe. Note that now a sudden expansion occurs after the elbow in the 1 1/2 in. pipe to a 2 1/2 in. pipe.
(b) Fluid flow through a horizontal circular pipe of inner radius of 2 cm with centerline velocity as shown in Table 1. Based on Table 1 and setting given to you; (i) Determine the average velocity, maximum velocity and volume flowrate; and (ii) Calculate and draw the velocity profile for the given flow. Table 1: Setting of Question Centerline Velocity (m/s) Density (kg/m³) Dynamic Viscosity (Pa.s) 1.0 1.225 1.802 x 10-5
4. Fluid flows axially in the annular space between a cylinder and a concentric rod. The radius of the rod is r; and that of the cylinder is ro. Fluid motion in the annular space is driven by an axial pressure gradient dp/dz. The cylinder is maintained at uniform temperature To. Assume incompressible laminar axisymmetric flow and neglect gravity and end effects. Show that the axial velocity is given by: _1-(r; /r, )? In(r, / r; ) r dp |(r/r,)? Au dz - In(r / r, ) – 1
The velocity profile in fully developed laminar flow in a circular pipe of inner radius ro, is given by v=9(1-7) Find: 1) Plot the velocity profile. 2) The volume of water flows out of the pipe in 0.2 min?
is used to determine major loss in pipe flow. Law of conservation of Energy Law of conservation of mass Law of conservation of momentum Darcy -Weisbach equation
Why an ideal flow of any fluid must satisfy continuity equation?
Sketch the shear stress and velocity distribution for laminar flow across a pipe section?
Consider a pipe on a horizontal plane: based on Bernoulli's equation A. none of the above B. the inlet velocity will be less than the outlet velocity C. the inlet velocity will be greater than the outlet velocity D. the elevation of the inlet will be greater than that of the outlet
Simulation of laminar gas flow in the pipe with Ansys Fluent Task: 1. Calculate velocity distribution in y axis at inlet and outlet of the pipe. Submit it as a chart. 2. Calculate velocity distribution over the pipe length. Submit it as a chart. Figure. pipe geometry L, m = 16 R, m= 0.15 Inlet velocity, m/s= 0.08 Gas= Oxygen Need proper solution like pdf file, don't need steps by steps. If you can can do it through ansys fluent. Write proper solution on word file or pdf.
A 1.0 m radius cylindrical industrial tank filled with viscous oil to a level at a height h from its base, must be drained through a tube with a radius of 0.2 m and length L, connected to its base. The speed profile of oil in the drain tube can be described by the equation below. Where v is the oil speed, vmax is a = maximum oil speed, r is the radius, and R is the tube radius. Considering this problem situation, do what is asked in the following items, justifying your answers. a) What is the volume, in liters, of oil removed from the tank after 10 seconds, if the maximum discharge speed does the oil reach 0.35 m/s? Data: π ≈ 22/7; 1 m3 = 1000 L. b) What flow regime does the system operate? Demonstrate. Data: specific mass of oil = 800 kg/m3, specific mass of water = 1000 kg/m3, oil viscosity = 0.056 Pa.s e viscosity of water = 0.001 Pa.s.
An oil (viscosity 1 Pa.s, density 800kg/m3) is flowing in an axisymmetric pipe. The flow is fully developed and laminar and the velocity at the centre of the pipe is = 30cm/s. The velocity cross-sectional profile is parabolic as: u(r) = U0(1- r2/R2) . Here r is the distance of the point to the pipe centre where the velocity is u(r). . R is radius of pipe (R=4mm). Calculate: the shear stress at the pipe wall the shear stress within the fluid 2 mm from the pipe wall the Reynold’s number of the flow
The dynamic equilibrium in circular pipe flow: Velocity profile in laminar flow CExplain in detail, diagram and formulas may be included!)