2. How will you be able to tell that your liquid sample is completely vaporized? How long will it approximately take for the sample to vaporize? 3. Given that 0.740 grams of unknown volatile liquid condensed into the 125-mL flask at 0.982 atm pressure and at 372 K temperature, what is the MW (molecular weight) of the unknown volatile liquid?

2. How will you be able to tell that your liquid sample is completely vaporized? How long will it approximately take for the sample to vaporize? 3. Given that 0.740 grams of unknown volatile liquid condensed into the 125-mL flask at 0.982 atm pressure and at 372 K temperature, what is the MW (molecular weight) of the unknown volatile liquid?

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

suppose your flask was heated for several minutes after all the unknown liquid had been vaporized. explain what effect, if any, this would have on your experimentally determined molar mass?
How to calculate the boiling point of methylene chloride at 670mm Hg? (need some hint)
On the basis of the distribution of kinetic energies of the molecules in a liquid, explain why increasing the liquid's temperature increases the rate of evaporation. Select all that apply. O The molecules with low kinetic energy are the first to evaporate. O The molecules with high kinetic energy are the first to evaporate. O As the temperature increases, the average kinetic energy of the molecules increases. O As the temperature increases, a larger fraction of the molecules have sufficient energy to escape from the liquid. O As the temperature increases, a smaller fraction of the molecules have sufficient energy to escape from the liquid. O None of these. eTextbook and Media Save for Later Attempts: 0 of 15 used Submit Answer МacBook Air 吕0 888 F5 F6 F7 F8 F9 F10 F3 F4 F2
Four liquids are described in the table below. Use the second column of the table to explain the order of their freezing points, and the third column to explain the order of their boiling points. For example, select '1' in the second column next to the liquid with the lowest freezing point. Select '2' in the second column next to the liquid with the next higher freezing point, and so on. In the third column, select '1' next to the liquid with the lowest boiling point, '2' next to the liquid with the next higher boiling point, and so on. Note: the density of water is 1.00 g/mL. solution 2.2 g of ethylene glycol (C₂H602) dissolved in 200. mL of water 2.2 g of sucrose (C12H22011) dissolved in 200. mL of water 2.2 g of potassium nitrate (KNO3) dissolved in 200. mL of water 200. mL of pure water freezing point (choose one) (choose one) (choose one) (choose one) X boiling point (choose one) (choose one) O (choose one) (choose one)
(a) Consider a substance where the intermolecular forces hold the molecules in fixed rigid positions. What is the process called when enough heat has been added to the substance so that the molecules begin to flow? (b) Consider a substance where the intermolecular forces hold the molecules in close contact with each other, but the molecules can flow. What is the process called when enough heat has been added to the substance so that the molecules escape each other? (c) Consider a substance where the intermolecular forces hold the molecules in fixed rigid positions. What is the process called when enough heat has been added to the substance so that the molecules can escape each other?
- Suppose a small sample of pure X is held at -236.°C and 2.0 atm. What will be the state of the sample (solid, liquid, or gas)? - Suppose the temperature is held constant at -236.°C but the pressure is decreased by 1.2 atm. What will happen to the sample (nothing, it will melt, it will freeze, it will boil, it will condense, it will sublime, or it will deposit)? - Suppose, on the other hand, the pressure is held constant at 2.0 atm but the temperature is increased by 137°C. What will happen to the sample (nothing, it will melt, it will freeze, it will boil, it will condense, it will sublime, or it will deposit)? All these are part of one question.
Substance X is known to exist at 1 atm in the solid, liquid, or vapor phase, depending on the temperature. Additionally, the values of these other properties of X I have been determined: melting point enthalpy of fusion temperature (°C) 120- 110- 100- 90- 80 70- 60- You may also assume X behaves as an ideal gas in the vapor phase. Suppose a small sample of X at 20 °C is put into an evacuated flask and heated at a constant rate until 10.0 kJ/mol of heat has been added to the sample. Graph the temperature of the sample that would be observed during this experiment. density 50+ 40 30- 20 65. °C 10.00 kJ/mol 3 2.80 g/cm³ (solid) 2.30 g/mL (liquid) 0 heat added (kJ/mol) 8 9 boiling point enthalpy of vaporization 10 heat capacity P 100. °C X 21.00 kJ/mol -1 38. J K mol (solid) 29. J.K¹ mol 48. J.K¹ mol 1 (liquid) (vapor) 2 00 ola Ar B
- Suppose a small sample of pure X is held at -182. °C and 0.8 atm. What will be the state of the sample (solid, liquid, or gas)? - Suppose the temperature is held constant at -182. °C but the pressure is increased by 0.3 atm. What will happen to the sample (nothing, it will melt, it will freeze, it will boil, it will condense, it will sublime, or it will deposit)? - Suppose, on the other hand, the pressure is held constant at 0.8 atm but the temperature is increased by 178.°C. What will happen to the sample (nothing, it will melt, it will freeze, it will boil, it will condense, it will sublime, or it will deposit)? This all part of one question
Four liquids are described in the table below. Use the second column of the table to explain the order of their freezing points, and the third column to explain the order of their boiling points. For example, select '1' in the second column next to the liquid with the lowest freezing point. Select '2' in the second column next to the liquid with the next higher freezing point, and so on. In the third column, select '1' next to the liquid with the lowest boiling point, '2' next to the liquid with the next higher boiling point, and so on. Note: the density of water is 1.00 g/mL. solution freezing point boiling point 2.0 g of ethylene glycol (C2H602) dissolved in 300. mL of water (choose one) (choose one) 2.0 g of potassium acetate (KCH3CO2) dissolved in 300. mL of water (choose one) (choose one) 2.0 g of glucose (C6H1206) dissolved in 300. mL of water (choose one) (choose one) 300. mL of pure water (choose one) (choose one)