2. For the inverter below, S1-S4 are 4 arms of inverter, they are composed of power electronic devices and auxiliary circuits. (1) When_and_are turned on, and_are turned off, load voltage is u,=Ua. (2) When S, and S4 are turned off, S2 and S3 are turned on, load voltage is u,-

Q: The rate of fall of current in a diode with reverse recovery charge and reverse recovery time of 40…

A: Given reverse recovery charge= 40 µC and reverse recovery time =7.5 µs

Q: hich of the following can’t be included in data required for coordination study? A)X/R ratio B)MVA…

A: characteristic curves of the fuses and breakers are generally analyzed in the coordination study

Q: The static characteristics of the measurement instrument are act

A: In this question, The static characteristics of the measurement instrument are act....?

Q: Which of the following layer is below the drift layer in non bunch through IGBT ? O a. p-layer O b.…

A: The IGBTs without n+ buffer layer is called as non-punch through IGBTs.

Q: When the load of a voltage multiplier is too small, __." Choices: the output voltage is unaffected…

A: Voltage multiplier is the circuit which is used to give high dc value of voltage at the output…

Q: The rubber used in the wheels of aero-plane is, a) Perfect insulator b) Slightly conducting c) Can…

A: The solution along with the explanation is provided in the following section.

Q: 65. What kind of device is a resistor? a. Unilateral b. Linear c. Nonlinear d. Polar 66. What kind…

A: Since you have posted the multiple questions so we are supposed to answer 3 questions only. 65)  In…

Q: b. Check the below statements and state whether these statements are true or False. Justify your…

A: knee voltage is a voltage at which the value of the forward current increasing rapidly.

Q: Draw the I-V characteristic of diodes and show the breakdown voltage, knee voltage on the graph.…

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: With neat diagram explain the construction and working of CRO.

A:

Q: recall the topcis of the electronic Device and circuits

A: There are many topics in EDC  These topics are  1- Semiconductor diode  2-Diode circuit

Q: The full form of PISO is

A: The full form of PISO is Parallel-in Serial-Out in  technology terminology PISO is acronym for lot…

Q: Q1\ Draw the bridge full wave rectifier and explain the operation of each part in the circuit. Q2\…

A: Rectifier is a  device which convert alternating signal in to pulsating direct signal. The diode is…

Q: What is the percentage of carbon residue? What is the importance of carbon residue?

A: 1) The carbon Residue value of fuel depends on the refinery processes employed in its manufacture.…

Q: Formulate approach boundaries in the light of exposed live parts

A: Nominal system voltage (Phase to Phase) Limited approach boundary Exposed movable conductor…

Q: Get 8 to 1 MUX using 2 to 1 MUXs

A: design the 8×1 multiplexer using 2×1 multiplexer. First let's calculate the number of 2×1…

Q: 3. (a) Discuss about the working principles of Light Emitting Diode (LED) with necessary figures.…

A: LED refers to light emitting diode, it is mainly used as it emits light when current flows through…

Q: In what types of semiconductors are holes the minority carriers? Please choose one: A) n-type B)…

A: Semiconductor

Q: The AND-OR implementation of PAL is having O a. Programmable AND array and Programmable OR array Ob.…

A: Given: Brief description: In the above given question they are discussing about the working of the…

Q: Determine 71000  mod 6 and  61001 mod 7

A: Determine 71000 mod 6 and 61001 mod 7 ?

Q: Consider an n-type semiconductor, in which minimum conductivity design criteria is applied. Select…

A: Given data:The semiconductor is of n-type.Minimum conductivity design criteria are…

Q: For The Volfage-divider bias configurafion of the hgure Shown below, determine: Vc ,VE B IBQ. I ca,…

A:

Q: State the different damages of diodes

A: Different damages of diodes: i) Short circuit  ii) Open circuit iii) Leakage situation.

Q: Rewrite five (5) proper steps in determining the sizing of battery that to be used  either in…

A: We need to write steps in determining the sizing of battery that to be used either in…

Q: b. Check the below statements and state whether these statements are true or False. Justify your…

A:

Q: Qg:- for dhe numbers below 1. (1011 o1) 2 ( loo1)e Find s- O muttipliantion of the two numbert 2…

A:

Q: Could you please go into more detail about how the Ac equivilant model was created? thank you

A: The AC equivalent model of the circuit need to be explained for the given volt

Q: 5) 68 TEC : 7

A: the TEC is the impedance that is VIx

Q: What is the difference between majority charge carrier and minority charge carrier?

A: Semiconductors have two types of charge carriers - electrons and holes. Electrons are negatively…

Q: An electrical component has a reliability of 0.95 over 1,500 hours of normal use (note normal use…

A: Given  Reliability = 0.95  Usage in hours = 1500 Here the electrical component usage indicates it…

Q: What are the types of Biomedical Instruments

A: Biomedical instrumentation is the field of engineering that applies the knowledge and technology for…

Q: All electronic components are formed from p type and n type materials. What factors determine what…

A: In p-type semiconductors, holes are the majority carriers and electrons are the minority carriers.…

Q: Types of error in the measuring intrument in short.

A: There are four types of error in measuring instrument, and these given in step-2.

Q: A single-phase half-wave thyristor control is desired to be designed in such a way that a rectifier…

A: Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: diff b/w aproximated & Interp0leted Curves. (Brief explanation with sketches)

A: Graphs are the pictorial representation of the system when we vary one quantity with respect to the…

Q: What is the voltage drop across the diode when it is connected in series to a resistor of 1.8 kilo…

A: we need to find out voltage drop across the diode.

Q: 9Vpk pk Vin Vout 1.25 2.25 3.75 4.50 -1.25 -2.25 -3.75 -4.50

A: We need to find out output voltage for given input values in clamper circuit .

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.