2. Find output voltage and current for a binary-weighted resistor DAC of 4 bits with given condition of R = 1kn, Rf = 5kn, VR = -12v and applied binary word is 1101'

Q: 5.5 If the three resistors in 6.4 were connected in parallel, what would be the reading on V1 and V;…

A:

Q: A nine volt source is used to power 2 electrical devices that are linked in parallel.The source's…

A: Circuit diagram as per our requirement :

Q: A certain wire has a resistance of 90 ohms. The resistance of another wire identical with the first…

A: The obstruction offered to the flow of electric current is called resistance. The electrical…

Q: R1 +V1 1 V R2 R3

A:

Q: The resistances of three resistors are 12, 15, and 9 ohms. These resistors are connected in parallel…

A: Given,  Three resistors are connected in parallel, let say R1=12 ohm,  R2= 15 ohm,  R3= 9 ohm…

Q: Answer the below questions for this electrical circuit where R1=20, R2=30, and R3=42. R, R2 8=12V R3…

A: Given circuit: E=12 VR1=2 ΩR2=3 ΩR3=4 Ω

Q: How do I solve this circuit? Find the voltage drop and current. If it is unsolvable please tell me…

A: Given : In the given question they have mentioned an electrical circuit having two voltage sources…

Q: WHICH OF THE ELECTRICAL SWITCHES (USING JUST ONE UNIT ONLY) CAN YOU USE TO PUT ON AND OFF…

A:

Q: 32. A resistive sensing-element R, is used in a voltage divider circuit as shown below. Which of the…

A:

Q: Make a circuit that controls two LED's with a single switch and has a single resistor. Make a…

A: a) We need to design a circuit that controls two LEDs with a single switch and has a single…

Q: b) Suppose the current in the 10 resistor in the following circuit A is 60 mA, flowing from left to…

A: We need to find out the current for given circuit

Q: give five designation, standards or abbreviations used in schematic diagrams

A: In order to represent a circuit in two dimensions we use Schematic diagrams In this representation…

Q: DETERMINE How MUCH poW ER DOES THE 6IVEN CIRCUIT CONSUME.

A: The given circuit is as shown below,

Q: I am confused on current drawn by R2, also power dissipated by R2

A:

Q: In the following circuit using Kirchhoff's find: a) The current in each branch of the circuit. b)…

A:

Q: Add one of the two features shown in the image below to this circuit diagram. Which I have also…

A: According to the question, in the given circuit model as shown below, We need to add one of the two…

Q: Draw bread board connection diagram of Full subtractor using 4:1 MUX.please give me the answer as…

A: The truth table is follows A B C sub BORR 0 0 0 0 0 0 0 1 1 1 0 1 1 1 1 0 1 0 0 1 1 0 1…

Q: Write a Boolean expression for the output of each of the logic circuits shown in Figure P7.27.

A: Given data, The OR gates are used to multiply the bits. The AND gates are used to add the bits.…

Q: What is the total area for the following Aluminum wire run? Six - 350 KCMIL XHHW Stranded Two -…

A: b) 3.7542 in²   To find the total area for the given Aluminum wire run, we need to calculate the…

Q: The resistances of three resistors are 12, 15, and 9 ohms. These resistors are connected in series…

A: given circuit

Q: What is the current through the LED? * R1 330 kOhm LED1 V1 LED_red 6 V A) OmA B) 23 mA C) 13 mA D)…

A: The solution is given below

Q: If Is = 3.84A E 7 Is 12 = 240mA Determine the following E or VT = 11 = 13 = R1 = www R₁ R2 = 500 1₁…

A: In this question We need to determine the unknown parameters.  We know As per ohms law, current in…

Q: Homeork-5: A resistor manufacturer produces carbon composition resistors of 100 MQ, with a tolerance…

A: A simple question based on colour coding  of resistances. In this the given value is 100Mohm and the…

Q: Answer in 4 sentences only 1) How does a multi - meter measure resistance??

A: Depending on the amount of accuracy required in the measurement, there are several techniques to…

Q: 3)Two wires have the following dimensions, the first is 5m length and 2cm2 in diameter the second is…

A: let R1 be a resistance of first wire R2 be a resistance of second wire R1 = resistivity×l1A1 l1…

Q: 6. Label each element of the circuit diagram [by the number]. What type of circuit is depicted in…

A: Given circuit,

Q: current source

A:

Q: Draw the schematic diagram of the following.

A: Introduction: In a single-phase supply, there are mainly two conductors:  Phase wire: The phase…

Q: 1. Identify the different symbols seen in the schematic diagram. Write it in a piece of paper and…

A: The given circuit is as shown below, We need to identify the symbols in the circuit and make a…

Q: 20 +12V travel

A: Voltage drop across each component

Q: Draw a schematic diagram containing a 2-cell battery (energy source), a switch, and 2 light bulbs…

A: The answer as given below steps:

Q: Draw and Illustrate the block diagram of the following. 1. External Device

A: Types of system Lines  Address line Data line Control line All the systems lines are connected to…

Q: 7) A wire has a resistance R are cut into 2 pieces and the small pieces are connect in parallel…

A:

Q: 1. Solve the tollowing unknowns. Tabulate your answer. R1 R2 Vs -ov R3

A:

Q: Answer parts 4,5&6

A:

Q: 4. Acar lot uses incandescent lamps to supply outside lighting during the night. There are three…

A:

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.